- 您現在的位置：買賣IC網 > PDF目錄98281 > TPS40055QPWPRQ1 (TEXAS INSTRUMENTS INC) SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | TPS40055QPWPRQ1 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | PLASTIC, HTSSOP-16 |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 571K |
| 代理商： | TPS40055QPWPRQ1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
www.ti.com
R
ILIM +
I
OC
R
DS(on)[max]
I
SINK
)
V
OS
I
SINK
(W)
(16)
SYNCHRONIZING TO AN EXTERNAL SUPPLY
R
T(dummy) +
1
f
SYNC
17.82
10*6
* 17 kW
(17)
R
KFF + VIN(min) * 3.5 V
58.14
R
T(dummy) ) 1340
W
(18)
Loop Compensation
A
MOD +
V
IN
V
S
or
A
MOD(dB) + 20
log
V
IN
V
S
(19)
D +
V
O
V
IN
+
V
C
V
S
or
V
O
V
C
+
V
IN
V
S
(20)
Calculate the Poles and Zeros
TPS40054-Q1, TPS40055-Q1, TPS40057-Q1
SLAS482A – AUGUST 2005 – REVISED NOVEMBER 2005
APPLICATION INFORMATION (continued)
The current limit programming resistor RILIM) is calculated using Equation 16. Care must be taken in choosing the
values used for VOS and ISINK in the equation. In order to assure the output current at the overcurrent level, the
minimum value of ISINK and the maximum value of VOS must be used.
where:
ISINK is the current into the ILIM pin and is 8.5 A, minimum
IOC is the overcurrent setpoint which is the DC output current plus one-half of the peak inductor current
VOS is the overcurrent comparator offset and is –20 mV, maximum
The TPS4005x can be synchronized to an external clock through the SYNC pin. Synchronization occurs on the
falling edge of the SYNC signal. The synchronization frequency should be in the range of 20% to 30% higher
than its programmed free-run frequency. The clock frequency at the SYNC pin replaces the master clock
generated by the oscillator circuit. Pulling the SYNC pin low programs the TPS4005x to freely run at the
frequency programmed by RT.
The higher synchronization must be factored in when programming the PWM ramp generator circuit. If the PWM
ramp is interrupted by the SYNC pulse, a UVLO condition is declared and the PWM becomes disabled. Typically
this is of concern under low-line conditions only. In any case, RKFF needs to be adjusted for the higher switching
frequency. In order to specify the correct value for RKFF at the synchronizing frequency, calculate a dummy value
for RT that would cause the oscillator to run at the synchronizing frequency. Do not use this value of RT in the
design.
Use the value of RT(dummy) to calculate the value for RKFF.
This value of RKFF ensures that UVLO is not engaged when operating at the synchronization frequency.
RT(dummy) is in k
Voltage-mode buck-type converters are typically compensated using Type III networks. Since the TPS4005x
uses voltage feedforward control, the gain of the PWM modulator with voltage feedforward circuit must be
included. The modulator gain is described in Figure 10, with VIN being the minimum input voltage required to
cause the ramp excursion to cover the entire switching period as described in Equation 19.
Duty cycle (D) varies from 0 to 1 as the control voltage )VC) varies from the minimum ramp voltage to the
maximum ramp voltage (VS). Also, for a synchronous buck converter, D = VO / VIN. To get the control voltage to
output voltage modulator gain in terms of the input voltage and ramp voltage:
For a buck converter using voltage mode control, there is a double pole due to the output L-CO. The double pole
is located at the frequency calculated in Equation 21.
16
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40054QPWPRQ1 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40070PWPRG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40071PWPR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40070PWPR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40074RHLT | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40056 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:WIDE-INPUT SYNCHRONOUS, TRACKING BUCK CONTROLLER |
| TPS40056PWP | 功能描述:DC/DC 開關控制器 Wide Vin Synch Buck DC/DC Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40056PWPG4 | 功能描述:DC/DC 開關控制器 Wide Vin Synch Buck DC/DC Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40056PWPR | 功能描述:DC/DC 開關控制器 Wide Vin Synch Buck DC/DC Contr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40056PWPRG4 | 功能描述:DC/DC 開關控制器 Wide Vin Synch Buck DC/DC Contr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。