- 您現在的位置：買賣IC網 > PDF目錄98282 > TPS53314RGFR (TEXAS INSTRUMENTS INC) SWITCHING REGULATOR, 1070 kHz SWITCHING FREQ-MAX, PQCC40 PDF資料下載
參數資料
| 型號： | TPS53314RGFR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, 1070 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 5 X 7 MM, GREEN, PLASTIC, VQFN-40 |
| 文件頁數： | 14/29頁 |
| 文件大小： | 800K |
| 代理商： | TPS53314RGFR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
( )
(
)
-
=
IN
OUT
OUT LL
SW
IN
V
1
I
2
L
f
V
(
)
( )
=
W
m
TRIP
V
mV
R
k
I
A
SLUSAK3
– MAY 2011
Auto-Skip Eco-mode
Light Load Operation
While the MODE pin is pulled low via RMODE, the TPS53314 automatically reduces the switching frequency at
light-load conditions to maintain high efficiency. Detailed operation is described as follows. As the output current
decreases from heavy load condition, the inductor current is also reduced and eventually comes to the point that
its rippled valley touches zero level, which is the boundary between continuous conduction and discontinuous
conduction modes. The synchronous MOSFET is turned off when this zero inductor current is detected. As the
load current further decreases, the converter runs into discontinuous conduction mode (DCM). The on-time is
maintained as it was in the continuous conduction mode so that it takes longer time to discharge the output
capacitor with smaller load current to the level of the reference voltage. The transition point to the light-load
operation IOUT(LL) (i.e., the threshold between continuous and discontinuous conduction mode) can be calculated
as shown in Equation 3.
where
SW is the PWM switching frequency
(3)
Switching frequency versus output current in the light load condition is a function of L, VIN and VOUT, but it
decreases almost proportionally to the output current from the IOUT(LL) given in Equation 3. For example, it is 60
kHz at IOUT(LL)/5 if the frequency setting is 300 kHz.
Adaptive Zero Crossing
The TPS53314 has an adaptive zero crossing circuit which performs optimization of the zero inductor current
detection at skip mode operation. This function pursues ideal low-side MOSFET turning off timing and
compensates inherent offset voltage of the Z-C comparator and delay time of the Z-C detection circuit. It
prevents SW-node swing-up caused by postponed detection and minimizes diode conduction period caused by
premature detection. As a result, better light-load efficiency is delivered.
Forced Continuous Conduction Mode
When the MODE pin is tied to PGOOD through a resistor, the controller keeps continuous conduction mode
(CCM) during light-load conditions. In this mode, the switching frequency is maintained over the entire load range
which is suitable for applications needing tight control of the switching frequency at a cost of lower efficiency.
Power Good
The TPS53314 has powergood output that indicates high when switcher output is within the target. The
powergood function is activated after soft-start has finished. If the output voltage becomes within +10% or
–5% of
the target value, internal comparators detect the powergood state and the powergood signal becomes high after
a 1-ms internal delay. If the output voltage goes outside of +15% or
–10% of the target value, the power-good
signal becomes low after two microsecond (2-
μs) internal delay. The powergood output is an open drain output
and must be pulled up externally.
In order for the PGOOD logic to be valid, the VDD input must be higher than 1 V. To avoid invalid PGOOD logic
before the TPS53314 is powered up, it is recommended the PGOOD be pull to VREG (either directly or through
a resistor divider) because VREG remains low when the device is off.
Current Sense and Overcurrent Protection
TPS53314 has cycle-by-cycle overcurrent limiting control. The inductor current is monitored during the OFF state
and the controller maintains the OFF state during the period in that the inductor current is larger than the
overcurrent trip level. In order to provide both good accuracy and cost effective solution, TPS53314 supports
temperature compensated MOSFET RDS(on) sensing. The TRIP pin should be connected to GND through the trip
voltage setting resistor, RTRIP. The TRIP pin sources ITRIP current, which is 10 μA typically at room temperature,
(4)
Copyright
2011, Texas Instruments Incorporated
21
相關PDF資料 |
PDF描述 |
|---|---|
| TPS53314RGFT | SWITCHING REGULATOR, 1070 kHz SWITCHING FREQ-MAX, PQCC40 |
| TPS53353DQPT | SWITCHING REGULATOR, PDSO22 |
| TPS53851RHHT | SWITCHING CONTROLLER, PQCC36 |
| TPS54010PWPG4 | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54040DGQ | 0.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS53314RGFT | 功能描述:直流/直流開關轉換器 4.5-25Vin,6A Step- Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS53315 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-A Step-Down Regulator with Integrated Switcher |
| TPS53315RGFR | 功能描述:直流/直流開關調節器 12A Step-Down Reg RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS53315RGFT | 功能描述:直流/直流開關調節器 12A Step-Down Reg RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS53316 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:High-Efficiency, 5-A Step-Down Regulator with Integrated Switcher |
發布緊急采購，3分鐘左右您將得到回復。