- 您現在的位置：買賣IC網 > PDF目錄98282 > TPS53314RGFT (TEXAS INSTRUMENTS INC) SWITCHING REGULATOR, 1070 kHz SWITCHING FREQ-MAX, PQCC40 PDF資料下載
參數資料
| 型號： | TPS53314RGFT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, 1070 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 5 X 7 MM, GREEN, PLASTIC, VQFN-40 |
| 文件頁數： | 17/29頁 |
| 文件大小： | 800K |
| 代理商： | TPS53314RGFT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
-
=
IN
OUT
INJ _ SW
SW
V
D
V
R7
C1
f
(
)
(
)
=
+
IND ripple
INJ _ OUT
IND ripple
OUT
SW
I
V
ESR
I
8
C
f
+
=
+
INJ _ SW
INJ _ OUT
VFB
V
0.6
2
-
=
OUT
FB
V
R1
R2
V
SLUSAK3
– MAY 2011
External Parts Selection with All Ceramic Output Capacitors
When ceramic output capacitors are used, the stability criteria in Equation 2 cannot be satisfied. The ripple
injection approach as shown in Equation 10 is implemented to increase the ripple on the VFB pin and make the
system stable. C2 can be fixed at 1 nF. The value of C1 can be selected between 10 nF to 200 nF.
The increased ripple on the VFB pin causes the increase of the VFB DC value. The AC ripple coupled to the
VFB pin has two components, one coupled from SW node and the other coupled from VOUT and they can be
calculated using Equation 10 and Equation 11.
(10)
(11)
The DC value of VFB can be calculated by Equation 12:
(12)
And the resistor divider value can be determined by Equation 13:
(13)
LAYOUT CONSIDERATIONS
Certain points must be considered before starting a layout work using the TPS53314.
The power components (including input/output capacitors, inductor and TPS53314) should be placed on one
side of the PCB (solder side). Other small signal components should be placed on another side (component
side). At least one inner plane should be inserted, connected to ground, in order to shield and isolate the
small signal traces from noisy power lines.
All sensitive analog traces and components such as VFB, PGOOD, TRIP, MODE and RF should be placed
away from high-voltage switching nodes such as LL, VBST to avoid coupling. Use internal layer(s) as ground
plane(s) and shield feedback trace from power traces and components.
Place the VIN decoupling capacitors as close to the VIN and PGND pins as possible to minimize the input AC
current loop.
Since the TPS53314 controls output voltage referring to voltage across the VOUT capacitor, the top-side
resistor of the voltage divider should be connected to the positive node of VOUT capacitor. In a same manner
both bottom side resistor and GND pad of the device should be connected to the negative node of VOUT
capacitor. The trace from these resistors to the VFB pin should be short and thin. Place on the component
side and avoid via(s) between these resistors and the device.
Connect the overcurrent setting resistors from TRIP pin to ground and make the connections as close as
possible to the device. The trace from TRIP pin to resistor and from resistor to ground should avoid coupling
to a high-voltage switching node.
Connect the frequency setting resistor from RF pin to ground, or to the VREG pin, and make the connections
as close as possible to the device. The trace from the RF pin to the resistor and from the resistor to ground
should avoid coupling to a high-voltage switching node.
Connect the MODE setting resistor from MODE pin to ground, or to the PGOOD pin, and make the
connections as close as possible to the device. The trace from the MODE pin to the resistor and from the
resistor to ground should avoid coupling to a high-voltage switching node.
The PCB trace defined as switch node, which connects the LL pins and high-voltage side of the inductor,
should be as short and wide as possible.
Connect the ripple injection VOUT signal (VOUT side of the C1 capacitor in Figure 34) from the terminal of
ceramic output capacitor. The AC coupling capacitor (C2 in Figure 34) should be placed near the device and
R7 and C1 can be placed near the power stage.
24
Copyright
2011, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS53353DQPT | SWITCHING REGULATOR, PDSO22 |
| TPS53851RHHT | SWITCHING CONTROLLER, PQCC36 |
| TPS54010PWPG4 | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54040DGQ | 0.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS54073PWPRG4 | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS53315 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-A Step-Down Regulator with Integrated Switcher |
| TPS53315RGFR | 功能描述:直流/直流開關調節器 12A Step-Down Reg RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS53315RGFT | 功能描述:直流/直流開關調節器 12A Step-Down Reg RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS53316 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:High-Efficiency, 5-A Step-Down Regulator with Integrated Switcher |
| TPS53316EVM-075 | 功能描述:電源管理IC開發工具 TPS53316 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。