- 您現在的位置：買賣IC網 > PDF目錄98282 > TPS54040DGQ (TEXAS INSTRUMENTS INC) 0.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 PDF資料下載
參數資料
| 型號： | TPS54040DGQ |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | PLASTIC, MSOP-10 |
| 文件頁數： | 28/47頁 |
| 文件大?。?/td> | 2435K |
| 代理商： | TPS54040DGQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
Under Voltage Lock Out Set Point
Output Voltage and Feedback Resistors Selection
Compensation
Ioutmax
p mod =
2 ×
× Vout × Cout
p
(41)
1
z mod =
2
Resr × Cout
p
(42)
p
z
f
=
co
mod
(43)
2
sw
p
f
=
co
mod
(44)
SLVS918 – MARCH 2009................................................................................................................................................................................................... www.ti.com
The Under Voltage Lock Out (UVLO) can be adjusted using an external voltage divider on the EN pin of the
TPS54040. The UVLO has two thresholds, one for power up when the input voltage is rising and one for power
down or brown outs when the input voltage is falling. For the example design, the supply should turn on and start
switching once the input voltage increases above 8.9V (enabled). After the regulator starts switching, it should
continue to do so until the input voltage falls below 7.9V (UVLO stop).
The programmable UVLO and enable voltages are set using a resistor divider between Vin and ground to the EN
pin. Equation 2 through Equation 3 can be used to calculate the resistance values necessary. For the example
application, a 332k
between Vin and EN and a 56.2k between EN and ground are required to produce the 8.9
and 7.9 volt start and stop voltages.
For the example design, 10.0 k
was selected for R2. Using Equation 1, R1 is calculated as 52.5 k. The
nearest standard 1% resistor is 52.3 k
. Due to current leakage of the VSENSE pin, the current flowing through
the feedback network should be greater than 1
A in order to maintain the output voltage accuracy. This
requirement makes the maximum value of R2 equal to 800 k
. Choosing higher resistor values will decrease
quiescent current and improve efficiency at low output currents but may introduce noise immunity problems.
There are several methods used to compensate DC/DC regulators. The method presented here is easy to
calculate and ignores the effects of the slope compensation that is internal to the device. Since the slope
compensation is ignored, the actual cross over frequency will usually be lower than the cross over frequency
used in the calculations. This method assume the crossover frequency is between the modulator pole and the
esr zero and the esr zero is at least 10 times greater the modulator pole. Use SwitcherPro software for a more
accurate design.
To get started, the modulator pole, fpmod, and the esr zero, fz1 must be calculated using Equation 41 and
Equation 42. For Cout, use a derated value of 21.2
f. Use equations Equation 43 and Equation 44, to estimate
a starting point for the crossover frequency, fco, to design the compensation. For the example design, fpmod is
753 Hz and fzmod is 1505 kHz. Equation 43 is the geometric mean of the modulator pole and the esr zero and
Equation 44 is the mean of modulator pole and the switching frequency. Equation 43 yields 33.7 kHz and
Equation 44 gives 16.2 kHz. Use the lower value of Equation 43 or Equation 44 for an initial crossover frequency.
For this example, fco is 16.2 kHz. Next, the compensation components are calculated. A resistor in series with a
capacitor is used to create a compensating zero. A capacitor in parallel to these two components forms the
compensating pole.
To determine the compensation resistor, R4, use Equation 45. Assume the power stage transconductance,
gmps, is 1.9A/V. The output voltage, Vo, reference voltage, VREF, and amplifier transconductance, gmea, are
3.3V, 0.8V and 92
A/V, respectively. R4 is calculated to be 77.1 k, use the nearest standard value of 76.8k.
Use Equation 46 to set the compensation zero to the modulator pole frequency. Equation 46 yields 2754 pF for
compensating capacitor C5, a 2700 pF is used on the board.
34
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS54040
相關PDF資料 |
PDF描述 |
|---|---|
| TPS54073PWPRG4 | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54073PWPR | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54073PWP | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS5410QDRQ1 | SWITCHING REGULATOR, PDSO8 |
| TPS54110PWP | 3.5 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS54040DGQ | 制造商:Texas Instruments 功能描述:Power Management IC 制造商:Texas Instruments 功能描述:IC, STEP-DOWN CONVERTER, MSOP-10 |
| TPS54040DGQR | 功能描述:直流/直流開關轉換器 3.5V-42Vin,0.5A Step Down SWIFT Convrtr RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS54040EVM-456 | 功能描述:電源管理IC開發工具 0.5A,12-42V In SWIFT Cnvrtr Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS54040EVM-456 | 制造商:Texas Instruments 功能描述:EVALUATION MODULE FOR TPS54040 SWIFT(TM) |
| TPS54040-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:0.5-A 42-V STEP-DOWN SWIFTa?￠ DC/DC CONVERTER WITH Eco-modea?￠ |
發布緊急采購，3分鐘左右您將得到回復。