欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TPS54040DGQ
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 0.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10
封裝: PLASTIC, MSOP-10
文件頁數: 33/47頁
文件大小: 2435K
代理商: TPS54040DGQ
Layout
BOOT
VIN
EN
SS/TR
RT/CLK
PH
GND
COMP
VSENSE
PWRGD
Input
Bypass
Capacitor
UVLO
Adjust
Resistors
SlowStart
Capacitor
Frequency
SetResistor
Compensation
Network
Resistor
Divider
Output
Inductor
Output
Capacitor
Vout
Vin
Topside
Ground
Area
Catch
Diode
RouteBootCapacitor
Traceonanotherlayerto
providewidepathfor
topsideground
ThermalVIA
SignalVIA
Estimated Circuit Area
www.ti.com................................................................................................................................................................................................... SLVS918 – MARCH 2009
Layout is a critical portion of good power supply design. There are several signals paths that conduct fast
changing currents or voltages that can interact with stray inductance or parasitic capacitance to generate noise
or degrade the power supplies performance. To help eliminate these problems, the VIN pin should be bypassed
to ground with a low ESR ceramic bypass capacitor with X5R or X7R dielectric. Care should be taken to
minimize the loop area formed by the bypass capacitor connections, the VIN pin, and the anode of the catch
diode. See Figure 63 for a PCB layout example. The GND pin should be tied directly to the power pad under the
IC and the power pad.
The power pad should be connected to any internal PCB ground planes using multiple vias directly under the IC.
The PH pin should be routed to the cathode of the catch diode and to the output inductor. Since the PH
connection is the switching node, the catch diode and output inductor should be located close to the PH pins,
and the area of the PCB conductor minimized to prevent excessive capacitive coupling. For operation at full rated
load, the top side ground area must provide adequate heat dissipating area. The RT/CLK pin is sensitive to noise
so the RT resistor should be located as close as possible to the IC and routed with minimal lengths of trace. The
additional external components can be placed approximately as shown. It may be possible to obtain acceptable
performance with alternate PCB layouts, however this layout has been shown to produce good results and is
meant as a guideline.
Figure 63. PCB Layout Example
The estimated printed circuit board area for the components used in the design of Figure 50 is 0.55 in2. This area
does not include test points or connectors.
Copyright 2009, Texas Instruments Incorporated
39
Product Folder Link(s): TPS54040
相關PDF資料
PDF描述
TPS54073PWPRG4 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28
TPS54073PWPR 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28
TPS54073PWP 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28
TPS5410QDRQ1 SWITCHING REGULATOR, PDSO8
TPS54110PWP 3.5 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20
相關代理商/技術參數
參數描述
TPS54040DGQ 制造商:Texas Instruments 功能描述:Power Management IC 制造商:Texas Instruments 功能描述:IC, STEP-DOWN CONVERTER, MSOP-10
TPS54040DGQR 功能描述:直流/直流開關轉換器 3.5V-42Vin,0.5A Step Down SWIFT Convrtr RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
TPS54040EVM-456 功能描述:電源管理IC開發工具 0.5A,12-42V In SWIFT Cnvrtr Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS54040EVM-456 制造商:Texas Instruments 功能描述:EVALUATION MODULE FOR TPS54040 SWIFT(TM)
TPS54040-Q1 制造商:TI 制造商全稱:Texas Instruments 功能描述:0.5-A 42-V STEP-DOWN SWIFTa?¢ DC/DC CONVERTER WITH Eco-modea?¢
主站蜘蛛池模板: 从江县| 额济纳旗| 阜康市| 晋江市| 西乌珠穆沁旗| 苏尼特右旗| 华安县| 惠来县| 松滋市| 尼木县| 梁山县| 乌兰浩特市| 武清区| 额尔古纳市| 普陀区| 察哈| 云霄县| 溧水县| 婺源县| 尉犁县| 张家口市| 泰和县| 海原县| 乌什县| 萝北县| 刚察县| 登封市| 黄梅县| 明星| 香河县| 雷州市| 吉安市| 读书| 进贤县| 滨海县| 城固县| 罗田县| 新丰县| 洪洞县| 张家港市| 如东县|