- 您現在的位置：買賣IC網 > PDF目錄98282 > TPS54225PWP (TEXAS INSTRUMENTS INC) 4.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14 PDF資料下載
參數資料
| 型號： | TPS54225PWP |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 4.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封裝： | GREEN, PLASTIC, HTSSOP-14 |
| 文件頁數： | 7/23頁 |
| 文件大小： | 733K |
| 代理商： | TPS54225PWP |
VOUT
VFB
VREG5
SS
GND
PG
EN
VCC
VIN
VBST
SW2
SW1
PGND1
PGND2
EXPOSED
POWERPAD
AREA
BOOST
CAPACITOR
VCC
INPUT
BYPASS
CAPACITOR
VOUT
VIA toGroundPlane
OUTPUT
INDUCTOR
OUTPUT
FILTER
CAPACITOR
SLOW
START
CAP
ANALOG
GROUND
TRACE
VIN
INPUT
BYPASS
CAPACITOR
VIN
FEEDBACK
RESISTORS
EtchonBottomLayer
orUnderComponent
ToEnable
Control
VCC
POWERGROUND
BIAS
CAP
Additional
Thermal
Vias
Additional
Thermal
Vias
Connectionto
POWERGROUND
oninternalor
bottomlayer
SLVSA15C
– OCTOBER 2009 – REVISED FEBRUARY 2011
LAYOUT CONSIDERATIONS
1. Keep the input switching current loop as small as possible.
2. Keep the SW node as physically small and short as possible to minimize parasitic capacitance and
inductance and to minimize radiated emissions. Kelvin connections should be brought from the output to the
feedback pin of the device.
3. Keep analog and non-switching components away from switching components.
4. Make a single point connection from the signal ground to power ground.
5. Do not allow switching current to flow under the device.
6. Keep the pattern lines for VIN and PGND broad.
7. Exposed pad of device must be connected to PGND with solder.
8. VREG5 capacitor should be placed near the device, and connected PGND.
9. Output capacitor should be connected to a broad pattern of the PGND.
10. Voltage feedback loop should be as short as possible, and preferably with ground shield.
11. Lower resistor of the voltage divider which is connected to the VFB pin should be tied to SGND.
12. Providing sufficient via is preferable for VIN, SW and PGND connection.
13. PCB pattern for VIN, SW, and PGND should be as broad as possible.
14. If VIN and VCC is shorted, VIN and VCC patterns need to be connected with broad pattern lines.
15. VIN Capacitor should be placed as near as possible to the device.
Figure 15. TPS54225 Layout
2009–2011, Texas Instruments Incorporated
15
Product Folder Link(s): TPS54225
相關PDF資料 |
PDF描述 |
|---|---|
| TPS54225PWPR | 4.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14 |
| TPS54225TPWPRQ1 | SWITCHING REGULATOR, PDSO14 |
| TPS54226PW | |
| TPS54227DDA | 4.7 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS54233DG4 | 2 A SWITCHING REGULATOR, 390 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS54225PWP | 制造商:Texas Instruments 功能描述:DC/DC STEP DOWN CONVERTER IC 700kHz HT 制造商:Texas Instruments 功能描述:IC, SYNC STEP-DOWN DC/DC CONV, HTSSOP-14 |
| TPS54225PWPR | 功能描述:直流/直流開關轉換器 4.5-18V 2A Sync Step Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS54225-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4.5V to 18V Input, 2-A Synchronous Step-Down SWIFTTM Converter |
| TPS54225TPWPRQ1 | 功能描述:直流/直流開關調節器 4.5V-18Vin,2A Sync Step-Down DCAP2 Mode RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS54226 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4.5V to 18V Input 2-A Synchronous Step-Down SWIFTTM Converter with Light Load Efficiency |
發布緊急采購，3分鐘左右您將得到回復。