欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TPS54418RTER
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 6.4 A SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PQCC16
封裝: 3 X 3 MM, GREEN, PLASTIC, WQFN-16
文件頁數: 21/35頁
文件大?。?/td> 1356K
代理商: TPS54418RTER
20
30
40
50
60
70
80
90
100
110
120
130
140
150
0
0.5
1
1.5
2
2.5
3
3.5
PowerDissapated(W)
T
Amax-Maximum
AmbientT
emperature-C
Tjmax=150 C,noairflow
°
SLVS946A – MAY 2009 – REVISED MAY 2010
www.ti.com
Figure 51. Maximum Ambient Temperature vs IC power Dissipation
LAYOUT
Layout is a critical portion of good power supply design. There are several signal paths that conduct fast
changing currents or voltages that can interact with stray inductance or parasitic capacitance to generate noise
or degrade the power supplies performance. Care should be taken to minimize the loop area formed by the
bypass capacitor connections and the VIN pins. See Figure 52 for a PCB layout example. The GND pins and
AGND pin should be tied directly to the power pad under the IC. The power pad should be connected to any
internal PCB ground planes using multiple vias directly under the IC. Additional vias can be used to connect the
top side ground area to the internal planes near the input and output capacitors. For operation at full rated load,
the top side ground area along with any additional internal ground planes must provide adequate heat dissipating
area.
Locate the input bypass capacitor as close to the IC as possible. The PH pin should be routed to the output
inductor. Since the PH connection is the switching node, the output inductor should be located very close to the
PH pins, and the area of the PCB conductor minimized to prevent excessive capacitive coupling. The boot
capacitor must also be located close to the device. The sensitive analog ground connections for the feedback
voltage divider, compensation components, slow start capacitor and frequency set resistor should be connected
to a separate analog ground trace as shown. The RT/CLK pin is particularly sensitive to noise so the RT resistor
should be located as close as possible to the IC and routed with minimal lengths of trace. The additional external
components can be placed approximately as shown. It may be possible to obtain acceptable performance with
alternate PCB layouts, however this layout has been shown to produce good results and is meant as a guideline.
28
Copyright 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): TPS54418
相關PDF資料
PDF描述
TPS54426PWP 7.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14
TPS54429PWP 0.01 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14
TPS5450MDDAREP 11.7 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8
TPS54519RTER 8 A SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PQCC16
TPS54612MPWPREP 12 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO28
相關代理商/技術參數
參數描述
TPS54418RTERG4 制造商:Texas Instruments 功能描述:
TPS54418RTET 功能描述:直流/直流開關調節器 2.95-6Vin 4A 2MHz Synch St Down RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS54424RNVT 功能描述:4.5V TO 17V INPUT, CURRENT MODE, 制造商:texas instruments 系列:SWIFT?? 包裝:剪切帶(CT) 零件狀態:在售 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入(最小值):4.5V 電壓 - 輸入(最大值):17V 電壓 - 輸出(最小值/固定):0.6V 電壓 - 輸出(最大值):12V 電流 - 輸出:4A 頻率 - 開關:200kHz ~ 1.6MHz 同步整流器:是 工作溫度:-40°C ~ 150°C(TJ) 安裝類型:表面貼裝 封裝/外殼:18-VFQFN 供應商器件封裝:18-VQFN-HR(3.5x3.5) 標準包裝:1
TPS54425 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-A OUTPUT SINGLE SYNCHRONOUS STEP DOWN SWITCHER WITH INTEGRATED FET ( SWIFT?)
TPS54425_10 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-A OUTPUT SINGLE SYNCHRONOUS STEP DOWN SWITCHER WITH INTEGRATED FET ( SWIFT?)
主站蜘蛛池模板: 宿州市| 保康县| 商水县| 闵行区| 禹城市| 高雄市| 濮阳市| 通州区| 通州市| 治多县| 双辽市| 大新县| 玛沁县| 望都县| 东乌| 商丘市| 招远市| 嘉兴市| 日喀则市| 镇沅| 榆中县| 乐东| 黎川县| 平南县| 潜江市| 万安县| 突泉县| 鲜城| 莫力| 金山区| 酒泉市| 乡城县| 佳木斯市| 区。| 长泰县| 华亭县| 黔西县| 漯河市| 汕尾市| 金湖县| 特克斯县|