
PRODUCTPREVIEW
SLVSAQ8A
– FEBRUARY 2011 – REVISED MAY 2011
PMIC FOR E Ink Vizplex
ENABLED ELECTRONIC PAPER
DISPLAY
1
FEATURES
Active Discharge on All Rails
Flexible Power-Up and Power Down
2345
Single Chip Power Management Solution for
Sequencing
E Ink Vizplex
Electronic Paper Displays
Integrated 10-
Ω, 3.3-V Power Switch for
Generates Positive and Negative Gate and
Disabling System Power Rail to E-Ink Panel
Source Driver Voltages and Back-Plane Bias
from a Single, Low-Voltage Input Supply
Thermistor Monitoring
Supports 9.7 Inch and Larger Panel Size
– –10°C to 85°C Temperature Range
3-V to 6-V Input Voltage Range
– ±1°C Accuracy from 0°C to 50°C
Boost Converter for Positive Rail Base
I2C Serial Interface
Inverting Buck-Boost Converter for Negative
– Slave Address 0x68h
Rail Base
Package Options:
Two Adjustable LDOs for Source Driver
– 48-Pin, 0.5 mm Pitch,
Supply
7 mm x 7 mm x 0.9 mm (QFN) RGZ
– LDO1: 15 V, 120 mA (VPOS)
– 48-Pin, 0.4 mm Pitch,
– LDO2: –15 V, 120 mA (VNEG)
6 mm x 6 mm x 0.9 mm (QFN) RSL
Accurate Output Voltage Tracking
APPLICATIONS
– VPOS - VNEG = ±50 mV
Power Supply for Active Matrix E Ink
Two Charge Pumps for Gate Driver Supply
Vizplex
Panels
– CP1: 22 V, 10 mA (VDDH)
EPD Power Supply
– CP2: –20 V, 12 mA, (VEE)
E-Book Readers
Adjustable VCOM Driver for Accurate
EPSON S1D13522 (ISIS) Timing Controller
Panel-Backplane Biasing
EPSON S1D13521 (Broadsheet) Timing
– User Programmable Default
Controller
– 0 V to -5.11 V
Application Processors With Integrated or
– ± 1.5% accuracy (±10 mV)
Software Timing Controller ( OMAP
)
– 9-Bit Control (10-mV Nominal Step Size)
DESCRIPTION
The TPS65185 is a single-chip power supply designed to for E Ink Vizplex
displays used in portable e-reader
applications and supports panel sizes up to 9.7 inches and greater. Two high efficiency DC/DC boost converters
generate
±16-V rails which are boosted to 22 V and –20 V by two change pumps to provide the gate driver
supply for the Vizplex
panel. Two tracking LDOs create the ±15-V source driver supplies which support up to
120-mA of output current. All rails are adjustable through the I2C interface to accommodate specific panel
requirements.
Accurate back-plane biasing is provided by a linear amplifier that can be adjusted from 0 V to -5.11 V with 9-bit
control through the serial interface and can source or sink current depending on panel condition. The TPS65185
supports automatic panel kickback voltage measurement which eliminates the need of manual VCOM calibration
in the production line. The measurement result can be stored in non-volatile memory to become the new VCOM
power-up default value.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
OMAP is a trademark of Texas Instruments.
3
Vizplex is a trademark of E Ink Corporation.
4
E Ink is a registered trademark of E Ink Corporation.
5
EPSON is a registered trademark of Seiko Epson Corporation.
PRODUCT PREVIEW information concerns products in the
Copyright
2011, Texas Instruments Incorporated
formative or design phase of development. Characteristic data and
other specifications are design goals. Texas Instruments reserves
the right to change or discontinue these products without notice.