- 您現在的位置：買賣IC網 > PDF目錄98286 > TPS65810RTQ (TEXAS INSTRUMENTS INC) 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 PDF資料下載
參數資料
| 型號： | TPS65810RTQ |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| 封裝： | 8 X 8 MM, ROHS COMPLIANT, PLASTIC, QFN-56 |
| 文件頁數： | 41/99頁 |
| 文件大小： | 2128K |
| 代理商： | TPS65810RTQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
www.ti.com
Using the Input Power to Run the System and Charge the Battery Pack
BATTERY CHARGE MANAGEMENT FUNCTION
Operating Modes
SLVS658B – MARCH 2006 – REVISED FEBRUARY 2007
An internal comparator with a fixed deglitch time, t DGL(NOBAT) monitors the ANLG1 pin voltage, if V(ANLG1) >
V(OUT) - VNOBATID a battery removed condition is detected and an internal discharge switch is activated,
connecting an internal resistor from BAT pin to AGND1. Note that ANLG1 can also be used as an analog input
for the ADC converter, in this case the voltage at pin ANLG1 must never exceed the V(OUT) - VNOBATID threshold
to avoid undesired battery discharge.
The external supply connected to AC or USB pins must be capable of supplying the system power and the
charger current. If the external supply power is not sufficient to run the system and charge the battery pack the
TPS65810 executes a two-stage algorithm that prevents a low voltage condition at the system power bus:
1. The charge current is reduced, until the total (charger + system current) is at a level that can be supplied by
the external input supply. This function is implemented by a dedicated charger control loop (see DPPM
section in charger functional description for additional details).
2. The battery switch is turned ON if the charge current is reduced to zero and the input current is not enough
to run the system. In this mode of operation both the battery and the external input power supply the system
power ( supplement operation mode).
The supplement operation mode is automatically set by the TPS65810 when the input power is switched to the
OUT pin, and the OUT pin voltage falls below the battery voltage.
The TPS65810 supports charging of single-cell Li-Ion or Li-Pol battery packs. The charge process is executed in
three phases: pre-charge (or pre-conditioning), constant current and constant voltage.
The charge parameters are selectable via I2C interface and using external components. The charge process
starts when an external input power is connected to the system, the charger is enabled by the I2C register
CHG_CONFIG bits CE=HI and CHGON=HI, and the battery voltage is below the recharge threshold, V(BAT) <
V(RCH). When the charge cycle starts a safety timer is activated. The safety timer timeout value is set by an
external resistor connected to the TMR pin.
When the charger is enabled two control loops modulate the battery switch drain to source impedance to limit the
BAT pin current to the programmed charge current value (charge current loop) or to regulate the BAT pin voltage
to the programmed charge voltage value (charge voltage loop). If V(BAT) < 3 V (typ) the BAT pin current is
internally set to 10% of the programmed charge current value. A typical charge profile is shown below, for an
operation condition that does not cause the IC junction temperature to exceed 125
°C (typ).
46
Copyright 2006–2007, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65810RTQT | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS65820RSHTG4 | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS65910RSLT | POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65920A2ZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920A2ZCH | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65810RTQR | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQRG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQT | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQTG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQR | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。