- 您現在的位置：買賣IC網 > PDF目錄98286 > TPS65810RTQ (TEXAS INSTRUMENTS INC) 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 PDF資料下載
參數資料
| 型號： | TPS65810RTQ |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| 封裝： | 8 X 8 MM, ROHS COMPLIANT, PLASTIC, QFN-56 |
| 文件頁數： | 58/99頁 |
| 文件大小： | 2128K |
| 代理商： | TPS65810RTQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
www.ti.com
Soft Start
Dropout Operation at 100% Duty Cycle
V(VIN_SM1) v V(SM1) ) I(L1) RDSON(PSM1) ) RL
(7)
Output Voltage Monitoring
Standby Mode
PWM Operation
SLVS658B – MARCH 2006 – REVISED FEBRUARY 2007
SM1 and SM2 have an internal soft start circuit that limits the inrush current during start-up. An initial delay (170
sec typ) from the converter enabled command to the converter effectively being operational is required, to
assure that the internal circuits of the converter are properly biased. At the end of that initial delay the soft start is
initiated, and the internal compensation capacitor is charged with a low value current source. The soft start time
is typically 750
s, with the output voltage ramping from 5% to 95% of the final target value.
The TPS65810 buck converters offer a low input to output voltage difference while still maintaining operation
when the duty cycle is set to 100%. In this mode of operation the P-channel switch is constantly turned on,
enabling operation with a low input voltage. The dropout operation starts if:
Where:
I(L1) = Output current plus inductor ripple current.
RL = DC resistance of the inductor
Equation 7 can be also used for the SM2 converter, replacing SM1 by SM2 and L1 by L2.
The output voltage of converters SM1 and SM2 is monitored by internal comparators, and an output low voltage
condition is detected when the output voltage is below 90% of the programmed value. The power good status for
SM1 and SM2 is accessible via I2C, see interrupt controller section for more details.
The power good comparators for SM1 and SM2 are disabled during the transition to standby mode operation.
They are enabled when the transition to standby mode is complete.
Using the I2C SM1 and SM2 can be set in stand-by mode. In STANDBY mode the PFM operation mode is set
and the output voltage is defined by I2C registers SM1_STANDBYand SM2_STANDBY, and it can be set to a
value different than the normal mode output regulation voltage. The standby mode can also be set by the GPIO
pins, if those are configured as control pins that define the SM1/SM2 operating mode.
During PWM operation the converters use a fast response voltage mode controller scheme with input voltage
feed-forward, enabling the use of small ceramic input and output capacitors. At the beginning of each clock cycle
the P-channel MOSFET switch is turned on, and the oscillator starts the voltage ramp. The inductor current
ramps up until the ramp voltage reaches the error amplifier output voltage, when the comparator trips and the
p-channel MOSFET switch is turned off. Internal adaptative break-before-make circuits turn on the integrated
n-channel MOSFET switch after an internal, fixed dead-time delay, and the inductor current ramps down, until
the next cycle is started. When the next cycle starts the ramp voltage is reset to its low value and the p-channel
MOSFET switch is turned on again.
Copyright 2006–2007, Texas Instruments Incorporated
61
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65810RTQT | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS65820RSHTG4 | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS65910RSLT | POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65920A2ZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920A2ZCH | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65810RTQR | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQRG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQT | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65810RTQTG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQR | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。