欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TPS65930A2ZCH
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PBGA139
封裝: 10 X 10 MM, 0.65 MM PITCH, GREEN, PLASTIC, NFBGA-139
文件頁數: 4/115頁
文件大小: 1232K
代理商: TPS65930A2ZCH
SWCS037G
– MAY 2008 – REVISED APRIL 2011
The timing requirements listed in Table 12-7 are valid on the following conditions of input slew and output
load:
Rise and fall time range of inputs (SYNC, DIN) is tR/tF = 1.0 ns/6.5 ns
Capacitance load range of outputs (CLK, SYNC, DOUT) is CLoad = 1 pF/30 pF
Table 12-7. TDM Interface Master Mode
—Timing Requirements
Notation
Parameter
Min
Max
Unit
T3
tsu(DIN-CLKH)
Setup time, TDM.DIN valid to TDM.CLK
25
ns
high
T4
th(DIN-CLKH)
Hold time, TDM.DIN valid from TDM.CLK
0
ns
high
Table 12-8 lists the switching characteristics of the TDM interface master mode.
Table 12-8. TDM Interface Master Mode
—Switching Characteristics
Notation
Parameter
Min
Max
Unit
T0
tc(CLK)
Cycle time, TDM.CLK (1)
1/64 * Fs
ns
T1
tw(CLK)
Pulse duration, TDM.CLK high or low(2)
0.45*P
0.55*P
ns
Delay time, TDM.CLK rising edge to TDM.SYNC
–10
10
ns
T2
td(CLKL-SYNC)
transition
Delay time, TDM.CLK rising edge to TDM.DOUT
–10
12
ns
T5
td(CLKL-DOUT)
transition
(1)
Fs = 8 to 48 kHz; 96 kHz for RX path only
(2)
P = TDM.CLK period
12.5 JTAG Interfaces
The TPS65920/TPS65930 device JTAG TAP controller handles standard IEEE JTAG interfaces. This
section describes the timing requirements for the tools used to test TPS65920/TPS65930 device power
management.
The JTAG/TAP module provides a JTAG interface according to IEEE Std1149.1a. This interface uses the
four I/O pins TMS, TCK, TDI, and TDO. The TMS, TCK, and TDI inputs contain a pullup device, which
makes their state high when they are not driven. The output TDO is a 3-state output, which is high
impedance except when data are shifted between TDI and TDO.
TCK is the test clock signal.
TMS is the test mode select signal.
TDI is the scan path input.
TDO is the scan path output.
TMS and TDO are multiplexed at the top level with the GPIO0 and GPIO1 pins. The dedicated external
TEST pin switches from functional mode (GPIO0/GPIO1) to JTAG mode (TMS/TDO). The JTAG
operations are controlled by a state-machine that follows the IEEE Std1149.1a state diagram. This
state-machine is reset by the TPS65920/TPS65930 internal power-on reset (POR). A test mode is
selected by writing a 6-bit word (instruction) into the instruction register and then accessing the related
data register.
Table 12-9 and Table 12-10 assume testing over the recommended operating conditions (see
Copyright
2008–2011, Texas Instruments Incorporated
Timing Requirements and Switching Characteristics
101
focus.ti.com: TPS65930/TPS65920
相關PDF資料
PDF描述
TPS65930BZCHR SPECIALTY CONSUMER CIRCUIT, PBGA139
TPS65930BZCH SPECIALTY CONSUMER CIRCUIT, PBGA139
TPS65950ZXNR SPECIALTY CONSUMER CIRCUIT, PBGA209
TPS65950ZXNT SPECIALTY CONSUMER CIRCUIT, PBGA209
TPS6735Y 2 A SWITCHING REGULATOR, 160 kHz SWITCHING FREQ-MAX, UUC12
相關代理商/技術參數
參數描述
TPS65930A2ZCHR 功能描述:PMIC 解決方案 Int Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
TPS65930BZCH 功能描述:開關變換器、穩壓器與控制器 Int Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
TPS65930BZCH 制造商:Texas Instruments 功能描述:IC POWER MANAGEMENT ((NW))
TPS65930BZCHR 功能描述:開關變換器、穩壓器與控制器 Int Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
TPS65950A2ZXN 功能描述:PMIC 解決方案 Integ Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
主站蜘蛛池模板: 盐池县| 七台河市| 海阳市| 河池市| 弥渡县| 甘德县| 日照市| 云龙县| 岳池县| 东丰县| 周宁县| 遵义市| 仁寿县| 台东市| 崇阳县| 台安县| 保定市| 玉山县| 铜鼓县| 蓝田县| 常德市| 吉木萨尔县| 运城市| 肃北| 闽侯县| 什邡市| 若尔盖县| 青岛市| 宜都市| 利辛县| 呼玛县| 罗江县| 电白县| 泗阳县| 略阳县| 右玉县| 汝州市| 镇安县| 禄劝| 新乡县| 鹤壁市|