欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TRF7960RHBT
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PQCC32
封裝: 5 X 5 MM, GREEN, PLASTIC, QFN-32
文件頁數: 15/52頁
文件大小: 1023K
代理商: TRF7960RHBT
SLOU186F – AUGUST 2006 – REVISED AUGUST 2010
www.ti.com
5.2.4
Direct Mode
Direct mode allows the user to configure the reader in one of two ways. Direct mode 0 (bit 6 = 0, as
defined in ISO control register) allows the user to use only the front-end functions of the reader, bypassing
the protocol implementation in the reader. For transmit functions, the user has direct access to the
transmit modulator through the MOD pin (pin 14). On the receive side, the user has direct access to the
sub-carrier signal (digitized RF envelope signal) on I/O_6 (pin 23).
Direct mode1 (bit 6 = 1, as defined in ISO control register) uses the sub-carrier signal decoder of the
selected protocol (as defined in ISO control register). This means that the receive output is not the
sub-carrier signal but the decoded serial bit stream and bit clock signals. The serial data is available on
I/O_6 (pin 23) and the bit clock is available on I/O_5 (pin 22). The transmit side is identical; the user has
direct control over the RF modulation through the MOD input. This mode is provided so that the user can
implement a protocol that has the same bit coding as one of the protocols implemented in the reader, but
needs a different framing format.
To select direct mode, the user must first choose which direct mode to enter by writing B6 in the ISO
control register. This bit determines if the receive output is the direct sub-carrier signal (B6 = 0) or the
serial data of the selected decoder. If B6 = 1, then the user must also define which protocol should be
used for bit decoding by writing the appropriate setting in the ISO control register.
The reader actually enters the direct mode when B6 (direct) is set to 1 in the chip status control register.
Direct mode starts immediately. The write command should not be terminated with a stop condition (see
communication protocol), because the stop condition terminates the direct mode and clears B6. This is
necessary as the direct mode uses one or two I/O pins (I/O_6, I/O_5). Normal parallel communication is
not possible in direct mode. Sending a stop condition terminates direct mode.
Figure 5-4 shows the different configurations available in direct mode.
In mode 0, the reader is used as an AFE only, and protocol handling is bypassed.
In mode 1, framing is not done, but SOF and EOF are present. This allows for a user-selectable
framing level based on an existing ISO standard.
In mode 2, data is ISO-standard formatted. SOF, EOF, and error checking are removed, so the
microprocessor receives only bytes of raw data via a 12-byte FIFO.
22
System Description
Copyright 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TRF7960 TRF7961
相關PDF資料
PDF描述
TRF7961RHBR SPECIALTY CONSUMER CIRCUIT, PQCC32
TRF7961RHBT SPECIALTY CONSUMER CIRCUIT, PQCC32
TS(X)8387MFDSSC/SMD 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
TS(X)8387MF_ 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
TS(X)8387VF_ 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
相關代理商/技術參數
參數描述
TRF7960RHBT 制造商:Texas Instruments 功能描述:RFID Reader IC 制造商:Texas Instruments 功能描述:IC, RFID READER, 13.56MHZ, QFN-32
TRF7960RHBTG4 功能描述:RFID應答器 Mulit-Standard High Freq RFID Read/Writ RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
TRF7960TB 功能描述:射頻識別變換器工具 TRF7960 Target Board RoHS:否 制造商:Olimex Ltd. 產品:RFID Readers 用于:ISO15693
TRF7961 制造商:TI 制造商全稱:Texas Instruments 功能描述:Multi-Standard Fully Integrated 13.56-MHz Radio Frequency Identification (RFID) Analog Front End and Data Framing Reader System
TRF7961RHBR 功能描述:RFID應答器 Multi-Standard High Freq RFid Reader RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
主站蜘蛛池模板: 客服| 梧州市| 平湖市| 会理县| 营山县| 阿拉尔市| 昔阳县| 桓台县| 桐梓县| 溆浦县| 邯郸县| 达孜县| 龙泉市| 云林县| 海宁市| 类乌齐县| 东台市| 名山县| 甘德县| 贵南县| 凌海市| 饶平县| 中牟县| 海城市| 渝北区| 郯城县| 荥阳市| 新郑市| 平邑县| 永胜县| 丰顺县| 和硕县| 宝坻区| 盐城市| 合水县| 义马市| 镇康县| 洛南县| 沂源县| 奉贤区| 安陆市|