- 您現在的位置：買賣IC網 > PDF目錄98286 > TRF7960RHBT (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQCC32 PDF資料下載
參數資料
| 型號： | TRF7960RHBT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 封裝： | 5 X 5 MM, GREEN, PLASTIC, QFN-32 |
| 文件頁數： | 25/52頁 |
| 文件大小： | 1023K |
| 代理商： | TRF7960RHBT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
www.ti.com
SLOU186F – AUGUST 2006 – REVISED AUGUST 2010
5.3.3
Status Registers
Table 5-22. IRQ Status Register (0Ch)
Displays the cause of IRQ and TX/RX status
Register default is set to 0x00 at POR = H or EN = L, and at each write to the ISO control register. It is also automatically reset at the end
of a read phase. The reset also removes the IRQ flag.
Bit
Bit Name
Function
Comments
B7
Irq_tx
IRQ set due to end of TX
Signals that TX is in progress. The flag is set at the start of TX but the
interrupt request is sent when TX is finished.
B6
Irg_srx
IRQ set due to RX start
Signals that RX SOF was received and RX is in progress. The flag is set at
the start of RX but the interrupt request is sent when RX is finished.
B5
Irq_fifo
Signals the FIFO is 1/3 > FIFO >
Signals FIFO high or low (less than 4 or more than 8)
2/3
B4
Irq_err1
CRC error
Indicates receive CRC error
B3
Irq_err2
Parity error
Indicates parity error
B2
Irq_err3
Byte framing or EOF error
Indicates framing error
B1
Irq_col
Collision error
For ISO14443A and ISO15693 single sub-carrier
B0
Irq_noresp
No-response interrupt
Signal to MCU that next slot command can be sent
Table 5-23. Collision Position and Interrupt Mask Register (0Dh)
Register default is set to 3E at POR = H and EN = L. Collision bits reset automatically after read operation.
Bit
Bit Name
Function
Comments
B7
Col9
Bit position of collision MSB
Supported: ISO15693, single sub-carrier, and ISO14443A
B6
Col8
Bit position of collision
B5
En_irq_fifo
Interrupt enable for FIFO
B4
En_irq_err1
Interrupt enable for CRC
B3
En_irq_err2
Interrupt enable for Parity
B2
En_irq_err3
Interrupt enable for Framing
error or EOF
B1
En_irq_col
Interrupt enable for collision
error
B0
En_irq_noresp
Enables no-response interrupt
Table 5-24. Collision Position (0Eh)
Displays the bit position of collision or error
Register default is set to 0x00 at POR = H and EN = L. Automatically reset after read operation.
Bit
Bit Name
Function
Comments
B7
Col7
Bit position of collision MSB
Supported is ISO15693, single sub-carrier, and ISO14443A
B6
Col6
In other protocols, it shows the bit position of error, either frame, SOF-EOF,
parity, or CRC error.
B5
Col5
B4
Col4
B3
Col3
B2
Col2
B1
Col1
B0
Col0
Bit position of collision LSB
Copyright 2006–2010, Texas Instruments Incorporated
System Description
31
相關PDF資料 |
PDF描述 |
|---|---|
| TRF7961RHBR | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TRF7961RHBT | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TS(X)8387MFDSSC/SMD | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS(X)8387MF_ | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS(X)8387VF_ | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TRF7960RHBT | 制造商:Texas Instruments 功能描述:RFID Reader IC 制造商:Texas Instruments 功能描述:IC, RFID READER, 13.56MHZ, QFN-32 |
| TRF7960RHBTG4 | 功能描述:RFID應答器 Mulit-Standard High Freq RFID Read/Writ RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| TRF7960TB | 功能描述:射頻識別變換器工具 TRF7960 Target Board RoHS:否 制造商:Olimex Ltd. 產品:RFID Readers 用于:ISO15693 |
| TRF7961 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Multi-Standard Fully Integrated 13.56-MHz Radio Frequency Identification (RFID) Analog Front End and Data Framing Reader System |
| TRF7961RHBR | 功能描述:RFID應答器 Multi-Standard High Freq RFid Reader RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。