欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TRF7961RHBR
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PQCC32
封裝: 5 X 5 MM, GREEN, PLASTIC, QFN-32
文件頁數: 30/52頁
文件大小: 1023K
代理商: TRF7961RHBR
SLOU186F – AUGUST 2006 – REVISED AUGUST 2010
www.ti.com
5.5
Reader Communication Interface
5.5.1
Introduction
The communication interface to the reader can be configured in two ways: a parallel 8-pin interface and a
Data_Clk or a serial peripheral interface (SPI).
These modes are mutually exclusive; only one mode can be used at a time in the application.
When the SPI interface is selected, the unused I/O_2, I/O_1, and I/O_0 pins must be hard-wired according
to Table 5-30. At power up, the reader samples the status of these three pins. If they are not the same (all
High or all Low) it enters one of the possible SPI modes.
The reader always behaves as the slave while the microcontroller (MCU) behaves as the master device.
The MCU initiates all communications with the reader and is also used to communicate with the higher
levels (application layer). The reader has an IRQ pin to prompt the MCU for attention if the reader detects
a response from the proximity/vicinity integrated circuit card (PICC/VICC).
Communication is initialized by a start condition, which is expected to be followed by an
Address/Command word (Adr/Cmd). The Adr/Cmd word is 8 bits long, and its format is shown in
Table 5-30. Pin Assignment in Parallel and Serial Interface Connection or Direct Mode
Pin
Parallel
Parallel-Direct
SPI with SS
SPI without SS
DATA_
DATA_CLK
DATA_CLK from master
CLK
I/O_7
A/D[7]
MOSI(1) = data-in (reader-in)
MOSI(1) = data-in
(reader-in)
I/O_6
A/D[6]
Direct mode, data out (sub-carrier or bit stream) MISO(2) = data-out (MCU-out)
MISO(2) = data-out
(MCU-out)
I/O_5(3)
A/D[5]
Direct mode, strobe – bit clock out
See Note 3
I/O_4
A/D[4]
SS – slave select(4)
I/O_3
A/D[3]
I/O_2
A/D[2]
at VDD
I/O_1
A/D[1]
at VDD
at VSS
I/O_0
A/D[0]
at VSS
IRQ
IRQ interrupt
(1)
MOSI – master out, slave in
(2)
MISO – master in, slave out
(3)
IO_5 pin is used only for information when data is put out of the chip (for example, reading 1 byte from the chip). It is necessary first to
write in the address of the register (8 clocks) and then to generate another 8 clocks for reading out the data. The IO_5 pin goes high in
this second 8 clocks. But for normal SPI operation this pin IO_5 is not used.
(4)
Slave-select pin active-low
Table 5-31. Address/Command Word Bit Distribution
Bit
Description
Bit Function
Address
Command
Bit 7
Command control bit
0 = address, 1 = command
0
1
Bit 6
Read/Write
1 = read, 0 = write
R/W
0
Bit 5
Continuous address mode
1 = Cont. mode
R/W
0
Bit 4
Address/Command bit 4
Adr 4
Cmd 4
Bit 3
Address/Command bit 3
Adr 3
Cmd 3
Bit 2
Address/Command bit 2
Adr 2
Cmd 2
Bit 1
Address/Command bit 1
Adr 1
Cmd 1
Bit 0
Address/Command bit 0
Adr 0
Cmd 0
36
System Description
Copyright 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TRF7960 TRF7961
相關PDF資料
PDF描述
TRF7961RHBT SPECIALTY CONSUMER CIRCUIT, PQCC32
TS(X)8387MFDSSC/SMD 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
TS(X)8387MF_ 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
TS(X)8387VF_ 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
TS(X)8387VF 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
相關代理商/技術參數
參數描述
TRF7961RHBRG4 功能描述:RFID應答器 Multi-Standard High Frequency RFID RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
TRF7961RHBT 功能描述:RFID應答器 Multi-Standard High Freq RFid Reader RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
TRF7961RHBT 制造商:Texas Instruments 功能描述:RFID Reader IC
TRF7961RHBTG4 功能描述:RFID應答器 Multi-Standard High Freq RFID Read/Writ RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
TRF7962A 制造商:TI 制造商全稱:Texas Instruments 功能描述:FULLY INTEGRATED 13.56-MHz RFID READER/WRITER IC FOR ISO15693/ISO18000-3 STANDARDS
主站蜘蛛池模板: 永定县| 工布江达县| 忻城县| 玉门市| 南京市| 岢岚县| 建湖县| 黔西| 密山市| 灵武市| 日喀则市| 甘德县| 太原市| 集贤县| 洪湖市| 安岳县| 广平县| 黑山县| 宁河县| 宜兰县| 大理市| 永昌县| 孝昌县| 友谊县| 夏津县| 彰化市| 宁武县| 青阳县| 房产| 江山市| 普安县| 平顺县| 怀集县| 山阳县| 九江县| 无棣县| 长海县| 兰考县| 海安县| 进贤县| 临城县|