- 您現在的位置：買賣IC網 > PDF目錄98287 > TRF7961RHBR (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQCC32 PDF資料下載
參數資料
| 型號： | TRF7961RHBR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 封裝： | 5 X 5 MM, GREEN, PLASTIC, QFN-32 |
| 文件頁數： | 35/52頁 |
| 文件大小： | 1023K |
| 代理商： | TRF7961RHBR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
b7
b6
b5
b4
b3
b2
b1
b0
Start
Condition
Stop
Condition
SCLK
DataIN
DataOut
50ns
SLOU186F – AUGUST 2006 – REVISED AUGUST 2010
www.ti.com
5.7
Serial Interface Communication
When an SPI interface is required, parallel I/O pins, I/O_2, I/O_1, and I/O_0, must be hard wired
according to Table 5-31. On power up, the reader looks for the status of these pins; if they are not the
same (not all high, or not all low), the reader enters into one of two possible SPI modes.
The serial communications work in the same manner as the parallel communications with respect to the
FIFO, except for the following condition. On receiving an IRQ from the reader, the MCU reads the reader's
IRQ register to determine how to service the reader. After this, the MCU must to do a dummy read to clear
the reader's IRQ status register. The dummy read is required in SPI mode because the reader's IRQ
status register needs an additional clock cycle to clear the register. This is not required in parallel mode
because the additional clock cycle is included in the Stop condition.
A procedure for a dummy read is as follows:
A. Starting the dummy read:
(a) When using slave select (SS): set SS bit low.
(b) When not using SS: start condition is when SCLK is high (See Table 5-30).
B. Send address word to IRQ status register (0Ch) with read and continuous address mode bits set to 1
(See Table 5-31).
C. Read 1 byte (8 bits) from IRQ status register (0Ch).
D. Dummy-read 1 byte from register 0Dh (collision position and interrupt mask).
E. Stopping the dummy read:
(a) When using slave select (SS): set SS bit high.
(b) When not using SS: stop condition when SCLK is high (See Table 5-30).
5.7.1
SPI Interface Without SS* (Slave Select) Pin
The serial interface without the slave select pin must use delimiters for the start and stop conditions.
Between these delimiters, the address, data, and command words can be transferred. All words must be 8
bits long with MSB transmitted first.
Figure 5-8. Serial – SPI Interface Communication (No SS* Pin)
In this mode, a rising edge on data-in (I/O_7, pin 24) while SCLK is high resets the serial interface and
prepares it to receive data. Data-in can change only when SCLK is low and is taken by the reader on the
SCLK rising edge. Communication is terminated by the stop condition when the data-in falling edge occurs
during a high SCLK period.
5.7.2
SPI Interface With SS* (Slave Select) Pin
The serial interface is in reset while the SS* signal is high. Serial data-in (MOSI) changes on the falling
edge, and is validated in the reader on the rising edge, as shown in Figure 5-9. Communication is
terminated when the SS* signal goes high.
All words must be 8 bits long with the MSB transmitted first.
40
System Description
Copyright 2006–2010, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TRF7961RHBT | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TS(X)8387MFDSSC/SMD | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS(X)8387MF_ | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS(X)8387VF_ | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS(X)8387VF | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TRF7961RHBRG4 | 功能描述:RFID應答器 Multi-Standard High Frequency RFID RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| TRF7961RHBT | 功能描述:RFID應答器 Multi-Standard High Freq RFid Reader RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| TRF7961RHBT | 制造商:Texas Instruments 功能描述:RFID Reader IC |
| TRF7961RHBTG4 | 功能描述:RFID應答器 Multi-Standard High Freq RFID Read/Writ RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| TRF7962A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FULLY INTEGRATED 13.56-MHz RFID READER/WRITER IC FOR ISO15693/ISO18000-3 STANDARDS |
發布緊急采購，3分鐘左右您將得到回復。