- 您現在的位置：買賣IC網 > PDF目錄365955 > TS80L186EC13 MICROPROCESSOR|16-BIT|CMOS|QFP|100PIN|PLASTIC PDF資料下載
參數資料
| 型號： | TS80L186EC13 |
| 英文描述： | MICROPROCESSOR|16-BIT|CMOS|QFP|100PIN|PLASTIC |
| 中文描述： | 微處理器| 16位|的CMOS | QFP封裝| 100引腳|塑料 |
| 文件頁數： | 7/57頁 |
| 文件大小： | 585K |
| 代理商： | TS80L186EC13 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
80C186EC/188EC, 80L186EC/188EC
Programmable Interrupt Controllers
The 80C186EC utilizes two 8259A compatible Pro-
grammable Interrupt Controllers (PIC) to manage
both internal and external interrupts. The 8259A
modules are configured in a master/slave arrange-
ment.
Seven of the external interrupt pins, INT0 through
INT6, are connected to the master 8259A module.
The eighth external interrupt pin, INT7, is connected
to the slave 8259A module.
There are a total of 11 internal interrupt sources
from the integrated peripherals: 4 Serial, 4 DMA and
3 Timer/Counter.
Timer/Counter Unit
The 80C186EC Timer/Counter Unit (TCU) provides
three 16-bit programmable timers. Two of these are
highly flexible and are connected to external pins for
external control or clocking. The third timer is not
connected to any external pins and can only be
clocked internally. However, it can be used to clock
the other two timer channels. The TCU can be used
to count external events, time external events, gen-
erate non-repetitive waveforms or generate timed in-
terrupts.
Serial Communications Unit
The 80C186EC Serial Communications Unit (SCU)
contains two independent channels. Each channel is
identical in operation except that only channel 0 is
directly supported by the integrated interrupt control-
ler (the channel 1 interrupts are routed to external
interrupt pins). Each channel has its own baud rate
generator and can be internally or externally clocked
up to one half the processor operating frequency.
Both serial channels can request service from the
DMA unit thus providing block reception and trans-
mission without CPU intervention.
Independent baud rate generators are provided for
each of the serial channels. For the asynchronous
modes, the generator supplies an 8x baud clock to
both the receive and transmit shifting register logic.
A 1x baud clock is provided in the synchronous
mode.
DMA Unit
The four channel Direct Memory Access (DMA) Unit
is comprised of two modules with two channels
each. All four channels are identical in operation.
DMA transfers can take place from memory to mem-
ory, I/O to memory, memory to I/O or I/O to I/O.
DMA requests can be external (on the DRQ pins),
internal (from Timer 2 or a serial channel) or soft-
ware initiated.
The DMA Unit transfers data as bytes only. Each
data transfer requires at least two bus cycles, one to
fetch data and one to deposit. The minimum clock
count for each transfer is 8, but this will vary depend-
ing on synchronization and wait states.
Chip-Select Unit
The 80C186EC Chip-Select Unit (CSU) integrates
logic which provides up to ten programmable chip-
selects to access both memories and peripherals. In
addition, each chip-select can be programmed to
automatically insert additional clocks (wait states)
into the current bus cycle, and/or automatically ter-
minate a bus cycle independent of the condition of
the READY input pin.
I/O Port Unit
The I/O Port Unit on the 80C186EC supports two
8-bit channels and one 6-bit channel of input, output
or input/output operation. Port 1 is multiplexed with
the chip select pins and is output only. Port 2 is mul-
tiplexed with the pins for serial channels 1 and 2. All
Port 2 pins are input/output. Port 3 has a total of 6
pins: four that are multiplexed with DMA and serial
port interrupts and two that are non-multiplexed,
open drain I/O.
Refresh Control Unit
The Refresh Control Unit (RCU) automatically gen-
erates a periodic memory read bus cycle to keep
dynamic or pseudo-static memory refreshed. A 9-bit
counter controls the number of clocks between re-
fresh requests.
A 12-bit address generator is maintained by the RCU
and is presented on the A12:1 address lines during
the refresh bus cycle. Address bits A19:13 are pro-
grammable to allow the refresh address block to be
located on any 8 Kbyte boundary.
Watchdog Timer Unit
The Watchdog Timer Unit (WDT) allows for graceful
recovery from unexpected hardware and software
upsets. The WDT consists of a 32-bit counter that
decrements every clock cycle. If the counter reach-
es zero before being reset, the WDTOUT pin is
7
相關PDF資料 |
PDF描述 |
|---|---|
| TS80C186EC13 | MICROPROCESSOR|16-BIT|CMOS|QFP|100PIN|PLASTIC |
| TS80C186EC20 | MICROPROCESSOR|16-BIT|CMOS|QFP|100PIN|PLASTIC |
| TS80L186EC-13 | 16-Bit Microprocessor |
| TS80L188EC13 | MICROPROCESSOR|16-BIT|CMOS|QFP|100PIN|PLASTIC |
| TS80L188EC-13 | 16-Bit Microprocessor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS80L188EB13 | 功能描述:IC MPU 16-BIT 3V 13MHZ 80-MQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA（25x25） 包裝:托盤 |
| TS80L188EC13 | 功能描述:IC MPU 16-BIT 3V 13MHZ 100-MQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:40 系列:MPC83xx 處理器類型:32-位 MPC83xx PowerQUICC II Pro 特點:- 速度:267MHz 電壓:0.95 V ~ 1.05 V 安裝類型:表面貼裝 封裝/外殼:516-BBGA 裸露焊盤 供應商設備封裝:516-PBGAPGE（27x27） 包裝:托盤 |
| TS-80S | 制造商:Ultimate Support Systems 功能描述:Silver Original Speaker Stand 制造商:ULTIMATE SUPPORT 功能描述:ORIGINAL SPEAKER STAND SILVER |
| TS81 | 功能描述:T-STRUT 1" X 8.12" ALUMINUM RoHS:是 類別:盒，外殼，支架 >> 卡架 - 配件 系列:VectorPak™ 標準包裝:1 系列:VectorPak™ 附件類型:EFP 模塊 適用于相關產品:PCB |
| TS810 | 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:Microprocessor Reset Circuit |
發布緊急采購，3分鐘左右您將得到回復。