- 您現在的位置：買賣IC網 > PDF目錄365980 > TSH94 (意法半導體) HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION PDF資料下載
參數資料
| 型號： | TSH94 |
| 廠商： | 意法半導體 |
| 英文描述： | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION |
| 中文描述： | 高速低的備用位置電源四路運算放大器 |
| 文件頁數： | 4/11頁 |
| 文件大小： | 107K |
| 代理商： | TSH94 |
TSH94
4/11
STANDBY MODE
V
CC
+
= 5V, V
CC
-
= -5V, T
amb
= 25
°
C (unless otherwise specified)
STANDBY POSITION
APPLICATIONS
SIGNAL MULTIPLEXING
STANDBY MODE
To put the device in standby, just apply a logic
level on thestandby MOS input. As ground isa vir-
tual level for the device, threshold voltage has
been refered to V
CC
+
at V
CC
+
- 1.6V typ.
In standby mode, the output goes in high imped-
ance in 200ns. Be aware that all maximum rating
must still be followed in this mode. It leads to
swing limitation while using the device in signal
multiplexing configuration with followers, differen-
tial input voltage must not exceed
±
5V limiting in-
put swing to 2.5Vpp.
SAMPLE AND HOLD
Symbol
Parameter
Min.
Typ.
Max.
Unit
V
SBY
Pin 8/9 Threshold Voltage for STANDBY Mode
V
CC
+
-2.2
V
CC
+
-1.6
V
CC
+
-1.0
V
I
CC SBY
Total Consumption
Standby 1 & 2 = 0
Standby 1 & 2 = 1
Standby 1 = 1, Standby 2 = 0
Input/Output Isolation (f = 1MHz to 10MHz)
Time from Standby Mode to Active Mode
Time from Active Mode to Standby Mode
Standby Driving Current
Output Leakage Current
Input Leakage Current
13.7
13.7
9.4
70
200
200
2
20
20
mA
I
sol
t
ON
t
OFF
I
D
I
OL
I
IL
dB
ns
ns
pA
pA
pA
LOGIC INPUT
STATUS
Standby 1
Standby 2
Op-Omp 2
Op-Amp 3
Op-Amp 1 & 4
0
0
1
1
0
1
0
1
Enable
Enable
Standby
Standby
Standby
Enable
Standby
Enable
Enable
Enable
Enable
Enable
V
CC
V
CC
standby
相關PDF資料 |
PDF描述 |
|---|---|
| TSH94I | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION |
| TSH95IN | Voltage-Feedback Operational Amplifier |
| TSH95 | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION |
| TSH95I | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION |
| TSH95ID | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSH94_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:High speed low power quad operational amplifier with standby position |
| TSH94I | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION |
| TSH94ID | 功能描述:運算放大器 - 運放 Quad Hi-Spd Lo-Power RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| TSH94IDT | 功能描述:運算放大器 - 運放 Quad Hi-Spd Lo-Power RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| TSH94IN | 功能描述:運算放大器 - 運放 REORD 511-TSH94ID RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。