- 您現在的位置：買賣IC網 > PDF目錄365980 > TSH94 (意法半導體) HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION PDF資料下載
參數資料
| 型號： | TSH94 |
| 廠商： | 意法半導體 |
| 英文描述： | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION |
| 中文描述： | 高速低的備用位置電源四路運算放大器 |
| 文件頁數： | 5/11頁 |
| 文件大小： | 107K |
| 代理商： | TSH94 |
TSH94
5/11
APPLICATIONS
VIDEO LINE TRANSCEIVER WITH REMOTE CONTROL
PRINTED CIRCUIT LAYOUT
As for any high frequency device, a few rules must
be observed when designing the PCB to get the
best performances from this high speed op amp.
From the most to the least important points :
K
Each
power
supply lead
by-passed to ground with a 10nF ceramic
capacitor very close to the device and
10
μ
F capacitor.
K
To provide low inductance and low resist-
ance common return, use a ground plane
or common point return for power and sig-
nal.
has
to
be
K
All leads must be wide and as short as pos-
sible especially for op amp inputs. This is in
order to decrease parasitic capacitance
and inductance.
K
Use small resistor values to decrease time
constant with parasitic capacitance.
K
Choose component sizes as small as pos-
sible (SMD).
K
On output, decrease capacitor load so as
to avoid circuit stability being degraded
which may cause oscillation. You can also
add a serial resistor in order to minimise its
influence.
相關PDF資料 |
PDF描述 |
|---|---|
| TSH94I | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION |
| TSH95IN | Voltage-Feedback Operational Amplifier |
| TSH95 | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION |
| TSH95I | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION |
| TSH95ID | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSH94_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:High speed low power quad operational amplifier with standby position |
| TSH94I | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION |
| TSH94ID | 功能描述:運算放大器 - 運放 Quad Hi-Spd Lo-Power RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| TSH94IDT | 功能描述:運算放大器 - 運放 Quad Hi-Spd Lo-Power RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| TSH94IN | 功能描述:運算放大器 - 運放 REORD 511-TSH94ID RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。