- 您現在的位置：買賣IC網 > PDF目錄382716 > UBA2050 (NXP Semiconductors N.V.) One-chip telephone ICs with speech, dialler and ringer functions(帶語音，撥號及振鈴功能的單片電話芯片) PDF資料下載
參數資料
| 型號： | UBA2050 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | One-chip telephone ICs with speech, dialler and ringer functions(帶語音，撥號及振鈴功能的單片電話芯片) |
| 中文描述： | 一個有語言，撥號及鈴聲功能（帶語音，撥號及振鈴功能的單片電話芯片集成電路芯片的電話） |
| 文件頁數： | 18/52頁 |
| 文件大?。?/td> | 278K |
| 代理商： | UBA2050 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
2000 May 19
18
Philips Semiconductors
Product specification
One-chip telephone ICs with speech,
dialler and ringer functions
UBA2050(A); UBA2051(A;C)
I
NTERNAL RESET CIRCUIT
(
PINS
CE/FDI
AND
CE/CSI)
A reset signal is internally generated to initialize the
UBA205xx as follows (see Fig.18):
By the on-chip Power-On Reset (POR) circuit as long as
V
DD
is lower than V
POR
When the voltage on pin CE/CSI and on pin CE/FDI are
both LOW for a time greater than the reset delay
time t
RD
.
When reset conditions are fulfilled, pins MDY/TONE and
DP/FL are set to high-impedance; pins DMO, KT, LED,
R1 to R4 and C1 to C4 are set to LOW.
C
HIP ENABLE AND FREQUENCY DISCRIMINATOR INPUT
(
PIN
CE/FDI)
This input is used to activate and initialize part of the
system. This pin together with the pin CE/CSI determines
which mode to enter (see Table 2) and detects line power
breaks during on-line states. To prevent the dialler from
reacting on voltage disturbances on the telephone line, a
time-out is active. The dialler returns to the standby state
if the voltage on both pins CE/CSI and CE/FDI is LOW for
a time greater than t
RD
.
In the exchange, several AC signals can be superimposed
on the DC signal, e.g. dialling tone, busy tone,
disturbances (such as line power breaks) and ringer
signal. The ringer signal is evaluated and checked if its
frequency is above a specified ringer frequency f
ring
. It is
assumed that the frequency at pin CE/FDI is the same as
the ringer frequency present on the telephone line.
The signal at this pin is half-wave rectified so that the
dialler can easily detect zero-crossing, especially at high
frequency.
During switching (on-hook/off-hook and pulse dialling) this
pin is protected by its ESD diodes. The maximum input
current on these diodes should be below 1 mA.
C
HIP ENABLE
/C
RADLE SWITCH INPUT
(
PIN
CE/CSI)
To distinguish between different operating states an extra
CE/CSI input is used. Comparable to the CE/FDI input, the
CE/CSI activates the dialler part. From that moment the
dialler part polls this input and the CE/FDI input regularly
for line power breaks during on-line states. When pins
CE/CSI and CE/FDI are set LOW for a time greater than
t
RD
, the standby state is entered. Pin CE/CSI is set HIGH
during the off-hook situation (basic application). The basic
states are shown in Table 2.
Table 2
UBA205xx basic states
Notes
1.
2.
Don’t care.
AC signal at pin CE/FDI.
During switching (on-hook/off-hook and pulse dialling) this
pin is protected by its ESD diodes. The maximum input
current on these diodes should be below 1 mA.
R
INGER MELODY
(
PIN
MDY/TONE)
When an incoming ringer signal at pin CE/FDI is valid, the
UBA205xx starts generating a melody via the MDY/TONE
output ringer hardware (see Fig.35). The signal at
pin MDY/TONE is a square wave signal (see Fig.19).
This melody follows the cadence of the ringer signal. Both
the melody and the volume can be selected via the
keyboard.
The melody frequencies and the duration are given in
Table 3. Table 8 shows how a melody can be selected by
pressing a key during ringing. The melody setting will be
stored in the memory.
The volume of the ringer circuit can be controlled by
changing the amplitude of the square wave. The voltage
level at pin MDY/TONE can be changed as shown in
Table 9. The volume setting will be stored in the memory.
MDY/TONE is a push-pull output. MDY/TONE is
high-impedance when V
DD
< V
POR
.
handbook, halfpage
MGM334
NOR
POR
OR
reset
CE/CSI
CE/FDI
Fig.18 Internal reset.
INPUT CE/CSI
INPUT CE/FDI
STATE
LOW
HIGH
LOW
LOW
X; note 1
HIGH
standby
handset
ringer; note 2
相關PDF資料 |
PDF描述 |
|---|---|
| UBA2050A | One-chip telephone ICs with speech, dialler and ringer functions(帶語音，撥號及振鈴功能的單片電話芯片) |
| UBA2051 | One-chip telephone ICs with speech, dialler and ringer functions |
| UBA2051A | One-chip telephone ICs with speech, dialler and ringer functions |
| UBA2051AT | One-chip telephone ICs with speech, dialler and ringer functions |
| UBA2051C | One-chip telephone ICs with speech, dialler and ringer functions |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UBA2050A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip telephone ICs with speech, dialler and ringer functions |
| UBA2050AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip telephone ICs with speech, dialler and ringer functions |
| UBA2050T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip telephone ICs with speech, dialler and ringer functions |
| UBA2051 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip telephone ICs with speech, dialler and ringer functions |
| UBA2051A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip telephone ICs with speech, dialler and ringer functions |
發布緊急采購，3分鐘左右您將得到回復。