- 您現在的位置：買賣IC網 > PDF目錄24570 > 051-053-9603229 (ITT Corporation) RF Coaxial Connectors PDF資料下載
參數資料
| 型號： | 051-053-9603229 |
| 廠商： | ITT Corporation |
| 英文描述： | RF Coaxial Connectors |
| 中文描述： | 射頻同軸連接器 |
| 文件頁數： | 22/42頁 |
| 文件大小： | 489K |
| 代理商： | 051-053-9603229 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Dimensions are shown in mm (inch)
Dimensions subject to change
130
RF Coaxial Connectors
Assembly Instructions
BAI-001
SMB/SMC Straight Connectors, Clamp Type for Braided Cable
1. Slide clamp nut, No. 1 washer, gasket and No. 2 washer over cable.
2. Trim cable to dimension shown taking care not to nick the braid.
3. Thumb braid out radially at right angles to dielectric.
4. A small chamfer may now be cut on the end of cable dielectric, to assist assembly of sleeve.
5. Slide sleeve over cable dielectric and under braid and outer jacket until the flange of the sleeve is
flush against the braid.
6. Move No.2 washer up to braid and trim braid flush with the flange of the sleeve.
7. Trim cable dielectric and center conductor to dimensions shown taking care not to nick the center
conductor.
8. Tin center conductor (DO NOT OVER TIN).
9. Slide rear insulator over cable.
10. Place a small solder preform made from 0,26 - 0,31 (.010 - .012) dia (28 swg) multi-core solder in
rear of contact.
11. Push contact on center conductor as far as possible. Heat center conductor and push until the
shoulder of the contact is flush against the rear insulator. Do not allow solder to protrude outside
spill hole.
12. Slide on front insulator flush against rear insulator (if not already assembled in body).
13. Move clamp nut, No. 1 washer and gasket up to No. 2 washer, slide on front body and tighten
clamp nut to required torque: 0,63 - 0,70 Nm (90 - 100 in. ozs.).
Only common cable retention features are shown in detail. Various body configurations can
apply.
CLAMP NUT
No. 1
WASHER
GASKET
No. 2
WASHER
SLEEVE
REAR
INSULATOR
CONTACT
FRONT
INSULATOR
FRONT
BODY
相關PDF資料 |
PDF描述 |
|---|---|
| 6QDP-064-03.75-SBR-TBL | INTERCONNECTION DEVICE |
| 6QDP-048-03.75-SBR-TBL | INTERCONNECTION DEVICE |
| 6QDPS-064-03.75-SBR-TBL | INTERCONNECTION DEVICE |
| 6QDPS-032-03.75-SBR-TBL | INTERCONNECTION DEVICE |
| 6QDPS-016-03.75-SBR-TBL | INTERCONNECTION DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 051-053-9603-229 | 制造商:ITT Interconnect Solutions 功能描述: |
| 051-054-0000-220 | 制造商:ITT Interconnect Solutions 功能描述:SMB 50OHM STRAIGHT BULKHEAD JACK - Bulk |
| 05105650000 | 制造商:WERA 功能描述:6PC LASER TIP ROUND BLADES PH1 PH2 WITH 4 SLOTTED/RACK |
| 05105650006 | 制造商:Wera 功能描述:Six Piece Kraftform Plus Lasertip Screwdriver Set with Round Blades |
| 05105656001 334/355/6 Rack | 制造商:Wera 功能描述:SLIP STOP SCREWDRIVER SET |
發布緊急采購，3分鐘左右您將得到回復。