- 您現在的位置：買賣IC網 > PDF目錄24570 > 051-053-9603229 (ITT Corporation) RF Coaxial Connectors PDF資料下載
參數資料
| 型號： | 051-053-9603229 |
| 廠商： | ITT Corporation |
| 英文描述： | RF Coaxial Connectors |
| 中文描述： | 射頻同軸連接器 |
| 文件頁數： | 32/42頁 |
| 文件大小： | 489K |
| 代理商： | 051-053-9603229 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Dimensions are shown in mm (inch)
Dimensions subject to change
139
Assy Insts
RF Coaxial Connectors
Assembly Instructions
BBAI-1243
QTTM 75
BNC Plug for Braided Cable
Cable
Cap Color
Cable Code
Die Size
Combined Assembly/
Crimp Tool Part Number
735A
Red
9019
4,52 (.178)
050-000-0030020
734
Dark Blue
9029
6,48 (.255)
050-000-0030040
M17/29-RG59/U
Light Blue
9039
6,48 (.255)
050-000-0030040
1694A
Black
9049
7,72 (.304)
050-000-0030010
CRIMP FERRULE
PLUG ASSEMBLY
ASSEMBLY TOOL
1. Prepare cable using a suitable stripping tool to the dimensions shown, being careful not to damage
the braid, dielectric, foil or inner conductor.
NOTE: Do not attempt to mate unterminated connectors.
2. ENSURE THAT THE INNER CONDUCTOR IS STRAIGHT.
After removal of the assembly tool from the crimp barrel (if fitted), slide crimp ferrule over the cable
sheath. Fit the plug assembly onto the cable so that the crimp barrel slides between the
dielectric/foil and the braid (gently twisting and rocking the plug assembly to spread the braid will
help). Care must be taken to ensure that no strands of braid are trapped under the body. The cable
must be inserted until the dielectric can be felt butting against the rear insulator.
3. Supporting the cable and plug asembly in one hand, press the front insulator fully home using the
assembly tool provided. A light pull on the cable will confirm the captivation of the center
conductor.
4. Slide the ferrule over braid until it butts up to the back of the connector. Crimp in position using an
ITT Cannon Crimp Tool and suitable die set (See table).
Alternative method, using combined assembly/crimp tool
Load the connector assembly into the combined assembly/crimp tool (see table) making sure that
the center pin is aligned with the hole in the dielectric bushing and the ferrule aligned in the die.
Close tool handles until ratchet releases. Allow tool handles to return to the open position and
remove crimped connector assembly.
相關PDF資料 |
PDF描述 |
|---|---|
| 6QDP-064-03.75-SBR-TBL | INTERCONNECTION DEVICE |
| 6QDP-048-03.75-SBR-TBL | INTERCONNECTION DEVICE |
| 6QDPS-064-03.75-SBR-TBL | INTERCONNECTION DEVICE |
| 6QDPS-032-03.75-SBR-TBL | INTERCONNECTION DEVICE |
| 6QDPS-016-03.75-SBR-TBL | INTERCONNECTION DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 051-053-9603-229 | 制造商:ITT Interconnect Solutions 功能描述: |
| 051-054-0000-220 | 制造商:ITT Interconnect Solutions 功能描述:SMB 50OHM STRAIGHT BULKHEAD JACK - Bulk |
| 05105650000 | 制造商:WERA 功能描述:6PC LASER TIP ROUND BLADES PH1 PH2 WITH 4 SLOTTED/RACK |
| 05105650006 | 制造商:Wera 功能描述:Six Piece Kraftform Plus Lasertip Screwdriver Set with Round Blades |
| 05105656001 334/355/6 Rack | 制造商:Wera 功能描述:SLIP STOP SCREWDRIVER SET |
發布緊急采購，3分鐘左右您將得到回復。