- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543G-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543G-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 93/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543G-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁當前第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
40
2008–2011 Teridian Semiconductor Corporation
v1.2
Table 25: The TCON Register Bit Functions (SFR 0x88)
Bit
Symbol
Function
TCON[7]
TF1
The Timer 1 overflow flag is set by hardware when Timer 1 overflows.
This flag can be cleared by software and is automatically cleared when an
interrupt is processed.
TCON[6]
TR1
Timer 1 run control bit. If cleared, Timer 1 stops.
TCON[5]
TF0
Timer 0 overflow flag set by hardware when Timer 0 overflows. This flag
can be cleared by software and is automatically cleared when an interrupt
is processed.
TCON[4]
TR0
Timer 0 Run control bit. If cleared, Timer 0 stops.
TCON[3]
IE1
Interrupt 1 edge flag is set by hardware when the falling edge on external
pin int1 is observed. Cleared when an interrupt is processed.
TCON[2]
IT1
Interrupt 1 type control bit. Selects either the falling edge or low level on
input pin to cause an interrupt.
TCON[1]
IE0
Interrupt 0 edge flag is set by hardware when the falling edge on external
pin int0 is observed. Cleared when an interrupt is processed.
TCON[0]
IT0
Interrupt 0 type control bit. Selects either the falling edge or low level on
input pin to cause interrupt.
2.4.8
WD Timer (Software Watchdog Timer)
There is no internal software watchdog timer. Use the standard hardware watchdog timer instead (see
2.4.9
Interrupts
The 80515 provides 11 interrupt sources with four priority levels. Each source has its own interrupt request
flag(s) located in a special function register (TCON, IRCON, and SCON). Each interrupt requested by the
corresponding flag can be individually enabled or disabled by the enable bits in IEN0 (SFR 0xA8), IEN1
(SFR 0xB8), and IEN2 (SFR 0x9A). Figure 12 shows the device interrupt structure.
Referring to Figure 12, interrupt sources can originate from within the 80515 MPU core (referred to as
Internal Sources) or can originate from other parts of the 71M6543 SoC (referred to as External Sources).
There are seven external interrupt sources, as seen in the leftmost part of Figure 12, and in Table 26 and
Table 27 (i.e., EX0-EX6).
Interrupt Overview
When an interrupt occurs, the MPU vectors to the predetermined address as shown in Table 38. Once
the interrupt service has begun, it can be interrupted only by a higher priority interrupt. The interrupt service
is terminated by a return from instruction, RETI. When an RETI is performed, the processor returns to the
instruction that would have been next when the interrupt occurred.
When the interrupt condition occurs, the processor also indicates this by setting a flag bit. This bit is set
regardless of whether the interrupt is enabled or disabled. Each interrupt flag is sampled once per
machine cycle, then samples are polled by the hardware. If the sample indicates a pending interrupt when
the interrupt is enabled, then the interrupt request flag is set. On the next instruction cycle, the interrupt is
acknowledged by hardware forcing an LCALL to the appropriate vector address, if the following conditions
are met:
No interrupt of equal or higher priority is already in progress.
An instruction is currently being executed and is not completed.
The instruction in progress is not RETI or any write access to the registers IEN0, IEN1, IEN2, IP0 or IP1.
Special Function Registers for Interrupts
The following SFR registers control the interrupt functions:
The interrupt enable registers: IEN0, IEN1 and IEN2 (see Table 26, Table 27 and Table 28).
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 722BG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 722MG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KK, PRES TEMP SENSOR - Bulk |
| 71M6543GT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KK, PRES TEMP SENSOR - Tape and Reel |
| 71M6543H | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543H-IGT/F | 功能描述:IC ENERGY METER 100-LQFP 制造商:maxim integrated 系列:Single Converter Technology? 包裝:托盤 零件狀態:停產 輸入阻抗:- 測量誤差:0.1% 電壓 - I/O 高:2V 電壓 - I/O 低:0.8V 電流 - 電源:- 電壓 - 電源:3 V ~ 3.6 V 表計類型:3 相 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-LQFP 供應商器件封裝:100-LQFP（14x14） 標準包裝:90 |
| 71M6543H-IGTR/F | 功能描述:IC ENERGY METER 100-LQFP 制造商:maxim integrated 系列:Single Converter Technology? 包裝:帶卷（TR） 零件狀態:停產 輸入阻抗:- 測量誤差:0.1% 電壓 - I/O 高:2V 電壓 - I/O 低:0.8V 電流 - 電源:- 電壓 - 電源:3 V ~ 3.6 V 表計類型:3 相 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-LQFP 供應商器件封裝:100-LQFP（14x14） 標準包裝:1,000 |
發布緊急采購，3分鐘左右您將得到回復。