- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8010R-IM (TERIDIAN SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, QCC32 PDF資料下載
參數資料
| 型號： | 73S8010R-IM |
| 廠商： | TERIDIAN SEMICONDUCTOR CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 封裝： | 5 X 5 MM, 0.80 MM HEIGHT, QFN-32 |
| 文件頁數： | 1/24頁 |
| 文件大小： | 333K |
| 代理商： | 73S8010R-IM |
73S8010R
Low Cost Smart Card Interface
DATA SHEET
Page: 1 of 24
2005 TERIDIAN Semiconductor Corporation
Rev 1.3
SEPTEMBER 2005
DESCRIPTION
The TERIDIAN 73S8010R is a single smart card interface
IC. The TERIDIAN 73S8010R has been designed to
provide full electrical compliance with ISO-7816-3 and
EMV 4.0 (EMV2000) specifications.
Interfacing with the host is done through the two-wire I
2C
bus, and one interrupt output to inform the system
controller of the card presence and faults.
The card clock signal can be generated by an on-chip
oscillator using an external crystal, or by connection to a
clock signal.
The TERIDIAN 73S8010R incorporates an ISO-7816-3
activation/deactivation sequencer that controls the card
signals. Level-shifters drive the card signals with the
selected card voltage (3V or 5V), coming from an internal
Low Drop-Out (LDO) voltage regulator. This LDO regulator
is powered by a dedicated power supply input VPC. Digital
circuitry is separately powered by a digital power supply
VDD.
With its embedded LDO regulator, the TERIDIAN
73S8010R is a cost-effective solution for any application
where a 5V (typically -5% +10%) power supply is
available.
Hardware support for auxiliary I/O lines, C4 / C8 contacts,
is provided.
Emergency card deactivation is initiated upon card
extraction or upon any fault generated by the protection
circuitry. The fault can be a card over-current, a VDD
(digital power supply), a VPC (regulator power supply), a
VCC (card power supply) or an over-heating fault.
The card over-current circuitry is a true current detection
function, as opposed to VCC voltage drop detection, as
usually implemented in ICC interface ICs.
The VDD voltage fault has a threshold voltage that can be
adjusted with an external resistor or resistor network. It
allows automated card deactivation at a customized VDD
voltage threshold value. It can be used, for instance, to
match the system controller operating voltage range.
APPLICATIONS
Set-Top-Box Conditional Access and Pay-per-
View
Point of Sales & Transaction Terminals
Control Access & Identification
Multiple card and SAM reader configurations
ADVANTAGES
Single smart card interface
IC firmware compatible with TDA8020
Traditional step-up converter is replaced by a
LDO regulator:
Greatly reduced power dissipation
Fewer external components are required
Better noise performance
High current capability (90mA supplied to the card)
Small format (5x5x0.8mm) QFN32 package option
True card over-current detection
FEATURES
Card Interface:
Complies with ISO-7816-3 and EMV 4.0
A LDO voltage regulator provides 3V / 5V to the
card from an external power supply input
Provides at least 90mA to the card
ISO-7816-3 Activation / Deactivation sequencer
with emergency automated deactivation on card
removal or fault detected by the protection circuitry
Protection includes 3 voltage supervisors that
detects voltage drops on VCC card and on power
supplies VDD and VPC
The VDD voltage supervisor threshold value can be
externally adjusted
Over-current detection 150mA max.
1 card detection input
Auxiliary I/O lines, for C4 / C8 contact signals
CLK signal up to 20MHz
Host Interface:
Fast mode, 400kbps I
2C slave bus
8 possible devices in parallel
One control register and one status register
Interrupt output to the host for fault detection
Crystal oscillator or host clock, up to 27MHz
Power Supply:
VPC: 4.75V to 5.5V
VDD: 2.7V to 5.5V
6kV ESD Protection on the card interface
Package: SO28 or QFN32
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8010R-IL | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8014BN-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 73S8014BN-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 73S8014RN-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 73S8014RN-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8010R-IM/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IM/F1 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IM/F2 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IMR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010R-IMR/F1 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。