欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: 73S8010R-IM
廠商: TERIDIAN SEMICONDUCTOR CORP
元件分類: 模擬信號調理
英文描述: SPECIALTY ANALOG CIRCUIT, QCC32
封裝: 5 X 5 MM, 0.80 MM HEIGHT, QFN-32
文件頁數: 21/24頁
文件大小: 333K
代理商: 73S8010R-IM
73S8010R
Low Cost Smart Card Interface
DATA SHEET
Page: 6 of 24
2005 TERIDIAN Semiconductor Corporation
Rev 1.3
I
2C-bus Write to Control Register:
I
2C-bus Write command to the control register follows the format shown below. After the START condition, a slave
address is sent by the master. This address is seven bits long followed by an eighth bit which is an opcode bit
(R/
W) – a ‘zero’ indicates the master will write data to the control register. After the R/W bit, the ’zero’ ACK bit is
sent to the master by the device. The master now starts sending the 8 bits of data to the control register during
the DATA bits. After the DATA bits, the ‘zero’ ACK bit is sent to the master by the device. The master should send
the STOP condition after receiving this ACK bit.
1-78
91-8
9
ADDRESSbits
R/
W bit
ACKbit
DATAbits
ACKbit
STOP
condition
START
condition
SCL
SDA
MSB
LSB
Figure 2 - I
2C Bus Write Protocol
STATUS register
Power On Reset = 04h
Name
Bit
Description
PRES
0
Set when the card is present (pin PRES is high); reset when the card is
not present.
PRESL
1
Set when the PRES pin changes state (rising/falling edge); reset when
the status register is read. Generates an interrupt when set.
I/O
2
Set when I/O is high; reset when I/O is low.
SUPL
3
Set when a voltage fault is detected; reset when the status register is
read. Generates an interrupt when set
PROT
4
Set when an over-current or over-heating fault has occurred during a
card session; reset when the status register is read. Generates an
interrupt when set
MUTE
5
Set during ATR when the card has not answered during the ISO 7816-3
time window (40000 card clock cycles); reset when the next session
begins.
EARLY
6
Set during ATR when the card has answered before 400 card clock
cycles; reset when the next session begin.
ACTIVE
7
Set when the card is active (VCC is on); reset when the card is inactive.
相關PDF資料
PDF描述
73S8010R-IL SPECIALTY ANALOG CIRCUIT, PDSO28
73S8014BN-ILR/F SPECIALTY ANALOG CIRCUIT, PDSO20
73S8014BN-IL/F SPECIALTY ANALOG CIRCUIT, PDSO20
73S8014RN-IL/F SPECIALTY ANALOG CIRCUIT, PDSO20
73S8014RN-ILR/F SPECIALTY ANALOG CIRCUIT, PDSO20
相關代理商/技術參數
參數描述
73S8010R-IM/F 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
73S8010R-IM/F1 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
73S8010R-IM/F2 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
73S8010R-IMR/F 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
73S8010R-IMR/F1 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
主站蜘蛛池模板: 秦皇岛市| 遂宁市| 泗水县| 丰都县| 武胜县| 新绛县| 自治县| 海宁市| 库尔勒市| 锦屏县| 台南县| 建昌县| 固镇县| 永吉县| 马边| 苗栗县| 涟源市| 诸城市| 永顺县| 太仆寺旗| 安国市| 宜章县| 方山县| 红安县| 长岭县| 綦江县| 会昌县| 大英县| 石河子市| 通化市| 桦南县| 夏津县| 大英县| 昭通市| 古交市| 聂拉木县| 兴仁县| 滨州市| 穆棱市| 台安县| 佛学|