- 您現在的位置：買賣IC網 > PDF目錄373911 > AD7641BCPZ (ANALOG DEVICES INC) 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC PDF資料下載
參數資料
| 型號： | AD7641BCPZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
| 中文描述： | 1-CH 18-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, QCC48 |
| 封裝： | 7 X 7 MM, LEAD FREE, MO-220VKKD-2, LFCSP-48 |
| 文件頁數： | 10/14頁 |
| 文件大小： | 192K |
| 代理商： | AD7641BCPZ |
AD7631/AD7634
Preliminary Technical Data
Pin
No.
11, 12
Rev. PrC | Page 10 of 14
Mnemonic
D[4:5]
or DIVSCLK[0:1]
Type
1
DI/O
Description
When MODE[1:0] = 0, 1, or 2, these pins are Bit 4 and Bit 5 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), serial clock division selection. When using serial master read
after convert mode (EXT/INT = low, RDC/SDIN = low), these inputs can be used to slow down the
internally generated serial clock that clocks the data output. In other serial modes, these pins are
high impedance outputs.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 6 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), serial clock source select. This input is used to select the
internally generated (master) or external (slave) serial data clock.
When EXT/INT = low, master mode. The internal serial clock is selected on SCLK output.
When EXT/INT = high, slave mode. The output data is synchronized to an external clock signal,
gated by CS, connected to the SCLK input.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 7 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), invert sync select. In serial master mode (EXT/INT = low), this
input is used to select the active state of the SYNC signal.
When INVSYNC = low, SYNC is active high.
When INVSYNC = high, SYNC is active low.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 8 of the parallel port data output bus.
When MODE[1:0] = 3, invert SCLK select. In all serial modes, this input is used to
invert the SCLK signal.
When MODE[1:0] = 0, 1, or 2, this output is used as bit 9 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), read during convert. When using serial master mode
(EXT/INT = low), RDC is used to select the read mode.
When RDC = high, the previous conversion result is output on SDOUT during conversion and
the period of SCLK changes.
When RDC = low (read after convert), the current result can be output on SDOUT only when
the conversion is complete.
When MODE[1:0] = 3 (serial mode), serial data in. When using serial slave mode, (EXT/INT = high),
SDIN could be used as a data input to daisy-chain the conversion results from two or more ADCs
onto a single SDOUT line. The digital data level on SDIN is output on SDOUT with a delay of 18 SCLK
periods after the initiation of the read sequence.
Input/Output Interface Digital Power Ground.
Input/Output Interface Digital Power. Nominally at the same supply as the supply of the
host interface (2.7 V to 5V).
Digital Power. Nominally at 5 V.
Digital Power Ground.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 10 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), serial data output. In serial mode, this pin is used as the serial
data output synchronized to SCLK. Conversion results are stored in an on-chip register. The ADC
provides the conversion result, MSB first, from its internal shift register. The data format is
determined by the logic level of OB/2C.
In master mode, EXT/INT = low. SDOUT is valid on both edges of SCLK.
In slave mode, EXT/INT = high:
When INVSCLK = low, SDOUT is updated on SCLK rising edge and valid on the next falling edge.
When INVSCLK = high, SDOUT is updated on SCLK falling edge and valid on the next rising edge.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 11 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), serial clock. In all serial modes, this pin is used as the serial
data clock input or output, depending upon the logic state of the EXT/INT pin. The active edge
where the data SDOUT is updated depends on the logic state of the INVSCLK pin.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 12 of the parallel port data output bus.
When MODE[1:0] = 3 (serial mode), frame synchronization. In serial master mode (EXT/INT= low),
this output is used as a digital output frame synchronization for use with the internal data clock.
13
D6
or EXT/INT
DI/O
14
D7
or INVSYNC
DI/O
15
D8
or INVSCLK
DI/O
16
D9
or RDC
DI/O
or SDIN
17
18
OGND
OVDD
P
P
19
20
21
DVDD
DGND
D10
or SDOUT
P
P
DO
22
D11
or SCLK
DI/O
23
D12
or SYNC
DO
相關PDF資料 |
PDF描述 |
|---|---|
| AD7641BCPZRL | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
| AD7641BSTZ | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
| AD7641BSTZRL | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
| AD7641 | 18-Bit, 2 MSPS SAR ADC |
| AD7641ACP | 18-Bit, 2 MSPS SAR ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7641BCPZRL | 功能描述:IC ADC 18BIT 2MSPS SAR 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7641BSTZ | 功能描述:IC ADC 18BIT 2MSPS SAR 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7641BSTZRL | 功能描述:IC ADC 18BIT 2MSPS SAR 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7641XST | 制造商:Analog Devices 功能描述: |
| AD7641XST-U3 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。