- 您現在的位置：買賣IC網 > PDF目錄373974 > AD7699 (Analog Devices, Inc.) 16-Bit, 8-Channel, 250 kSPS PulSAR㈢ ADC. PDF資料下載
參數資料
| 型號： | AD7699 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 16-Bit, 8-Channel, 250 kSPS PulSAR㈢ ADC. |
| 中文描述： | 16位，8通道，250 kSPS的PulSAR系列㈢ADC的。 |
| 文件頁數： | 10/20頁 |
| 文件大小： | 2041K |
| 代理商： | AD7699 |
AD7689
Preliminary Technical Data
TERMINOLOGY
Least Significant Bit (LSB)
The LSB is the smallest increment that can be represented by a
converter. For an analog-to-digital converter with N bits of
resolution, the LSB expressed in volts is
Rev. PrC | Page 10 of 20
N
REF
2
V
LSB
(V)
=
Integral Nonlinearity Error (INL)
INL refers to the deviation of each individual code from a line
drawn from negative full scale through positive full scale. The
point used as negative full scale occurs LSB before the first
code transition. Positive full scale is defined as a level 1 LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line (see Figure 12).
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Offset Error
The first transition should occur at a level LSB above analog
ground (38.14
μ
V). The unipolar offset error is the deviation of
the actual transition from that point.
Gain Error
The last transition (from 111…10 to 111…11) should occur for
an analog voltage 1 LSB below the nominal full-scale. The gain
error is the deviation in LSB (or % of full-scale range) of the
actual level of the last transition from the ideal level after the
offset error is adjusted out. Closely related is the full-scale error
(also in LSB or % of full-scale range), which includes the effects
of the offset error.
Aperture Delay
Aperture delay is the measure of the acquisition performance. It
is the time between the rising edge of the CNV input and when
the input signal is held for a conversion.
Transient Response
Transient response is the time required for the ADC to accurately
acquire its input after a full-scale step function is applied.
Dynamic Range
Dynamic range is the ratio of the rms value of the full scale to
the total rms noise measured with the inputs shorted together.
The value for dynamic range is expressed in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Signal-to-(Noise + Distortion) Ratio (SINAD)
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in decibels.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in decibels.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels, between the rms amplitude
of the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD by the following formula:
ENOB
= (
SINAD
dB
1.76)/6.02
and is expressed in bits.
Channel-to-Channel Crosstalk
Channel-to-channel crosstalk is a measure of the level of crosstalk
between any two adjacent channels. It is measured by applying a
DC to the channel under test and applying a full-scale, 100 kHz
sine wave signal to the adjacent channel(s). The crosstalk is the
amount of signal that leaks into the test channel and is
expressed in dB.
Reference Voltage Temperature Coefficient
Reference voltage temperature coefficient is derived from the
typical shift of output voltage at 25°C on a sample of parts at the
maximum and minimum reference output voltage (V
REF
) meas-
ured at T
MIN
, T(25°C), and T
MAX
. It is expressed in ppm/°C as
(
)
C
ppm/
(
°
REF
V
6
10
)
–
(
)
C
25
(
)
(
–
)
×
×
=
°
MIN
T
MAX
T
REF
REF
REF
Min
V
Max
V
TCV
where:
V
REF
(
Max
) = maximum V
REF
at T
MIN
, T(25°C), or T
MAX
.
V
REF
(
Min
) = minimum V
REF
at T
MIN
, T(25°C), or T
MAX
.
V
REF
(25°
C
) = V
REF
at 25°C.
T
MAX
= +85°C.
T
MIN
= –40°C.
相關PDF資料 |
PDF描述 |
|---|---|
| ADA4851-4 | Low Cost, High Speed, Rail-to-Rail, Output Op Amps |
| ADA4851-2 | Low Cost, High Speed, Rail-to-Rail, Output Op Amps |
| ADA4899-1 | Unity Gain Stable, Ultralow Distortion, 1 nV/ Hz Voltage Noise, High Speed Op Amp |
| ADA4899-1YCPZ-R2 | Unity Gain Stable, Ultralow Distortion, 1 nV/ Hz Voltage Noise, High Speed Op Amp |
| ADA4899-1YCPZ-R7 | Unity Gain Stable, Ultralow Distortion, 1 nV/ Hz Voltage Noise, High Speed Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7699BCBZ-RL7 | 功能描述:8 CH 500KSPS 16BIT ADC IC 制造商:analog devices inc. 系列:* 包裝:剪切帶（CT） 零件狀態:在售 封裝/外殼:20-UFBGA，WLCSP 供應商器件封裝:20-WLCSP（2.39x2.39） 標準包裝:1 |
| AD7699BCPZ | 功能描述:IC ADC 8CH 16BIT 500KSPS 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7699BCPZRL7 | 功能描述:IC ADC 8CH 16BIT 500KSPS 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7701 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS 16-Bit A/D Converter |
| AD7701AN | 功能描述:IC ADC 16BIT LC2MOS 20-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。