- 您現在的位置：買賣IC網 > PDF目錄373914 > AD7715AN-3 (ANALOG DEVICES INC) 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC PDF資料下載
參數資料
| 型號： | AD7715AN-3 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| 中文描述： | 1-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDIP16 |
| 封裝： | 0.300 INCH, PLASTIC, MS-001AB, DIP-16 |
| 文件頁數： | 9/31頁 |
| 文件大?。?/td> | 474K |
| 代理商： | AD7715AN-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
AD7715
–9–
REV. C
Communications Register (RS1, RS0 = 0, 0)
The Communications Register is an eight-bit register from which data can either be read or to which data can be written. All com-
munications to the part must start with a write operation to the Communications Register. The data written to the Communications
Register determines whether the next operation is a read or write operation and to which register this operation takes place. Once the
subsequent read or write operation to the selected register is complete, the interface returns to where it expects a write operation to
the Communications Register. This is the default state of the interface, and on power-up or after a
RESET
, the AD7715 is in this
default state waiting for a write operation to the Communications Register. In situations where the interface sequence is lost, if a
write operation to the device of sufficient duration (containing at least 32 serial clock cycles) takes place with DIN high, the AD7715
returns to this default state. Table I outlines the bit designations for the Communications Register.
Table I. Communications Register
0/
DRDY
ZERO
RS1
RS0
R/
W
STBY
G1
G0
0/
DRDY
For a write operation, a 0 must be written to this bit so that the write operation to the Communications Reg-
ister actually takes place. If a 1 is written to this bit, the part will not clock on to subsequent bits in the regis-
ter. It will stay at this bit location until a 0 is written to this bit. Once a 0 is written to this bit, the next 7 bits
will be loaded to the Communications Register. For a read operation, this bit provides the status of the
DRDY
flag from the part. The status of this bit is the same as the
DRDY
output pin.
For a write operation, a 0
must
be written to this bit for correct operation of the part. Failure to do this will
result in unspecified operation of the device. For a read operation, a 0 will be read back from this bit location.
Register Selection Bits. These bits select to which one of four on-chip registers the next read or write opera-
tion takes place as shown in Table II along with the register size. When the read or write to the selected regis-
ter is complete, the part returns to where it is waiting for a write operation to the Communications Register.
It does not remain in a state where it will continue to access the selected register.
Read/Write Select. This bit selects whether the next operation is a read or write operation to the selected
register. A 0 indicates a write cycle as the next operation to the appropriate register, while a 1 indicates a read
operation from the appropriate register.
ZERO
RS1– RS0
R/
W
Table II. Register Selection
RS1
RS0
Register
Register Size
0
0
1
1
0
1
0
1
Communications Register
Setup Register
Test Register
Data Register
8 Bits
8 Bits
8 Bits
16 Bits
STBY
Standby. Writing a 1 to this bit puts the part in its standby or power-down mode. In this mode, the part
consumes only 10
μ
A of power supply current. The part retains its calibration and control word information
when in STANDBY. Writing a 0 to this bit places the part in its normal operating mode. The default value
for this bit after power-on or RESET is 0.
G2
G1
Gain Setting
0
0
1
0
1
2
1
0
32
1
1
128
相關PDF資料 |
PDF描述 |
|---|---|
| AD7715AN-5 | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| AD7715AR-3 | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| AD7715AR-5 | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| AD7715* | 3 V/5 V. 450 uA 16-Bit. Sigma-Delta ADC |
| AD7715ACHIPS-3 | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7715AN-5 | 功能描述:IC ADC 16BIT 5V 16-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7715ANZ-3 | 功能描述:IC ADC 16BIT SIGMA-DELTA 16DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7715ANZ-31 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 450 ??A 16-Bit, Sigma-Delta ADC |
| AD7715ANZ-5 | 功能描述:IC ADC 16BIT 5V 16-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7715ANZ-5 | 制造商:Analog Devices 功能描述:A/D Converter (A-D) IC |
發布緊急采購，3分鐘左右您將得到回復。