- 您現在的位置：買賣IC網 > PDF目錄373915 > AD7720BRU (ANALOG DEVICES INC) CMOS Sigma-Delta Modulator PDF資料下載
參數資料
| 型號： | AD7720BRU |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | CMOS Sigma-Delta Modulator |
| 中文描述： | 1-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 232K |
| 代理商： | AD7720BRU |
AD7720
–11–
REV. 0
R
100
V
C
2.7nF
VIN(+)
VIN(–)
C
2.7nF
C
2.7nF
R
100
V
Figure 24. Differential Input with Antialiasing
A capacitor between the two input pins sources or sinks charge
to allow most of the charge that is needed by one input to be
effectively supplied by the other input. T his minimizes undesir-
able charge transfer from the analog inputs to and from ground.
T he series resistor isolates the operational amplifier from the
current spikes created during the sampling process and provides
a pole for antialiasing. T he 3 dB cutoff frequency (f
3 dB
) of the
antialias filter is given by Equation 1, and the attenuation of the
filter is given by Equation 2.
f
3 dB
= 1/(2
π
R
EX T
C
EX T
)
(1)
Attenuation
= 20 log
1/ 1
+
f
/
f
3
dB
(
)
2
(2)
T he choice of the filter cutoff frequency will depend on the
amount of roll off that is acceptable in the passband of the
digital filter and the required attenuation at the first image
frequency.
T he capacitors used for the input antialiasing circuit must have
low dielectric absorption to avoid distortion. Film capacitors
such as Polypropylene, Polystyrene or Polycarbonate are suitable.
If ceramic capacitors are used, they must have NPO dielectric.
Applying the Reference
T he reference circuitry used in the AD7720 includes an on-chip
+2.5 V bandgap reference and a reference buffer circuit. T he
block diagram of the reference circuit is shown in Figure 25.
T he internal reference voltage is connected to REF1 via a
3 k
resistor and is internally buffered to drive the analog
modulator’s switched capacitor DAC (REF2). When using the
internal reference, connect 100 nF between REF1 and AGND.
If the internal reference is required to bias external circuits, use
an external precision op amp to buffer REF1.
3k
V
REFERENCE
BUFFER
1V
2.5V
REFERENCE
SWITCHED-CAP
DAC REF
REF1
REF2
COMPARATOR
100nF
Figure 25. Reference Circuit Block Diagram
T he AD7720 can operate with its internal reference or an external
reference can be applied in two ways. An external reference can
be connected to REF1, overdriving the internal reference. How-
ever, there will be an error introduced due to the offset of the
internal buffer amplifier. For lowest system gain errors when
using an external reference, REF1 is grounded (disabling the
internal buffer) and the external reference is connected to REF2.
In all cases, since the REF2 voltage connects to the analog
modulator, a 220 nF capacitor must connect directly from
REF2 to AGND. T he external capacitor provides the charge
required for the dynamic load presented at the REF2 pin
(Figure 26).
F
A
F
B
F
B
4pF
F
A
F
B
F
A
F
B
MCLK
REF2
F
A
4pF
SWITCHED-CAP
DAC REF
220nF
Figure 26. REF2 Equivalent Circuit
T he AD780 is ideal to use as an external reference with the
AD7720. Figure 27 shows a suggested connection diagram.
AD780
1
2
3
4
8
7
6
5
NC
+V
IN
TEMP
GND
O/P
SELECT
NC
V
OUT
TRIM
22nF
1
m
F
REF2
22
m
F
220nF
REF1
+5V
Figure 27. External Reference Circuit Connection
Input Circuits
Figures 28 and 29 show two simple circuits for bipolar mode
operation. Both circuits accept a single-ended bipolar signal
source and create the necessary differential signals at the input
to the ADC.
T he circuit in Figure 28 creates a 0 V to 2.5 V signal at the
VIN(+) pin to form a differential signal around an initial bias
voltage of 1.25 V. For single-ended applications, best T HD
performance is obtained with VIN(–) set to 1.25 V rather than
2.5 V. T he input to the AD7720 can also be driven differen-
tially with a complementary input as shown in Figure 29.
In this case, the input common-mode voltage is set to 2.5 V.
T he 2.5 V p-p full-scale differential input is obtained with a
1.25 V p-p signal at each input in antiphase. T his configuration
minimizes the required output swing from the amplifier circuit
and is useful for single supply applications.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7721 | CMOS 16-Bit, 468.75 kHz, Sigma-Delta ADC |
| AD7721AN | CMOS 16-Bit, 468.75 kHz, Sigma-Delta ADC |
| AD7721AR | CMOS 16-Bit, 468.75 kHz, Sigma-Delta ADC |
| AD7721SQ | CMOS 16-Bit, 468.75 kHz, Sigma-Delta ADC |
| AD7722 | 16-Bit, 195 kSPS CMOS, Sigma-Delta ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7720BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 25Msps 16-bit Serial 28-Pin TSSOP T/R |
| AD7720BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 25Msps 16-bit Serial 28-Pin TSSOP T/R 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| AD7720BRUZ | 功能描述:IC MODULATOR SIGMA-DELTA 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7720BRUZ-REEL | 功能描述:IC MODULATOR SIGMA-DELTA 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7720BRUZ-REEL7 | 功能描述:IC MODULATOR SIGMA-DELTA 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。