- 您現在的位置：買賣IC網 > PDF目錄373916 > AD7777AN (ANALOG DEVICES INC) LC2MOS, High Speed 1-, 4- & 8-Channel 10-Bit ADCs PDF資料下載
參數資料
| 型號： | AD7777AN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | LC2MOS, High Speed 1-, 4- & 8-Channel 10-Bit ADCs |
| 中文描述： | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDIP28 |
| 封裝： | PLASTIC, DIP-28 |
| 文件頁數： | 10/12頁 |
| 文件大小： | 220K |
| 代理商： | AD7777AN |
AD7776/AD7777/AD7778
–10–
REV. 0
Short Circuit Current
T his is defined as the maximum current which will flow either
into or out of the REFOUT pin if this pin is shorted to any
potential between 0 V and V
CC
. T his condition can be allowed
for up to 10 seconds provided that the power dissipation of the
package is not exceeded.
Signal-to-Noise and Distortion Ratio, S/(N+D)
Signal-to-noise and distortion ratio, S/(N+D), is the ratio of the
rms value of the measured input signal to the rms sum of all
other spectral components below the Nyquist frequency, includ-
ing harmonics but excluding dc. T he value for S/(N+D) is given
in decibels.
T otal Harmonic Distortion, T HD
T otal harmonic distortion is the ratio of the rms sum of the first
five harmonic components to the rms value of a full-scale input
signal and is expressed in decibels. For the AD7776/AD7777/
AD7778, total harmonic distortion (T HD) is defined as:
(V
22
+ V
32
+ V
42
+ V
5
2
+ V
62
)
1/2
V
1
20
log
=
where
V
1
is the rms amplitude of the fundamental and
V
2
,
V
3
,
V
4
, V
5
and
V
6
are the rms amplitudes of the individual
harmonics.
Intermodulation Distortion, IMD
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products, of order (m + n), at sum and difference frequencies of
mfa + nfb, where m, n = 0, 1, 2, 3. Intermodulation terms are
those for which m or n is not equal to zero. For example, the
second order terms include (fa + fb) and (fa – fb) and the third
order terms include (2 fa + fb), (2 fa – fb), (fa + 2 fb) and (fa –
2 fb).
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of cross-
talk between channels. It is measured by applying a full-scale
100 kHz sine wave signal to any one of the input channels and
monitoring the remaining channels. T he figure given is the
worst case across all channels.
DIGIT AL SIGNAL PROCE SSING APPLICAT IONS
In digital signal processing (DSP) application areas like voice
recognition, echo cancellation and adaptive filtering, the dy-
namic characteristics S/(N+D), T HD & IMD of the ADC are
critical. T he AD7776/AD7777/AD7778 are specified dynami-
cally as well as with standard dc specifications. Because the
track/hold amplifier has a wide bandwidth, an antialiasing filter
should be placed on the analog inputs to avoid aliasing of high
frequency noise back into the bands of interest.
T he dynamic performance of the ADC is evaluated by applying
a sine wave signal of very low distortion to a single analog input
which is sampled at a 380.95 kHz sampling rate. A fast Fourier
transform (FFT ) plot or histogram plot is then generated from
which the signal to noise and distortion, harmonic distortion
and dynamic differential nonlinearity data can be obtained.
Similarly, for intermodulation distortion, an input signal con-
sisting of two pure sine waves at different frequencies is applied
to the AD7776/AD7777/AD7778.
Figure 11 shows a 2048 point FFT plot for a single channel of
the AD7778 with an input signal of 99.88 kHz. T he SNR is
58.71 dB. It can be seen that most of the harmonics are buried
in the noise floor. It should be noted that the harmonics are
taken into account when calculating the S/(N+D).
0
–90
–80
0
–60
–40
–20
99.88
S
FREQUENCY – kHz
INPUT FREQUENCY =
99.88 kHz
SAMPLE FREQUENCY =
380.95 kHz
SNR = 58.7 dB
T
A
= +25
C
Figure 11. ADC FFT Plot
T he relationship between S/(N+D) and resolution (n) is ex-
pressed by the following equation:
S/
(
N
+
D
) =
(
6.02
n
+ 1.76
) dB
T his is for an ideal part with no differential or integral linearity
errors. T hese errors will cause a degradation in S/(N+D). By
working backwards from the above equation, it is possible to get
a measure of ADC performance expressed in effective number
of bits (n).
S/
(
N+D
)
(
dB
) – 1.76
n(effective) =
6.02
T he effective number of bits plotted vs. frequency for a single
channel of the AD7778 is shown in Figure 12. T he effective
number of bits is typically 9.5.
10
7.5
189.2
9
8
8.5
0
9.5
INPUT FREQUENCY – kHz
E
SAMPLE FREQUENCY = 378.4 kHz
T
A
= +24
C
Figure 12. Effective Number of Bits vs. Frequency
相關PDF資料 |
PDF描述 |
|---|---|
| AD7777AR | LC2MOS, High Speed 1-, 4- & 8-Channel 10-Bit ADCs |
| AD7778 | LC2MOS, High Speed 1-, 4- & 8-Channel 10-Bit ADCs |
| AD7778AS | LC2MOS, High Speed 1-, 4- & 8-Channel 10-Bit ADCs |
| AD7778* | LC2MOS. High Speed 1-. 4- & 8-Channel 10-Bit ADCs |
| AD7782 | Read Only, Pin Configured 24-Bit ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7777ANZ | 功能描述:IC ADC 10BIT 4CHAN HS 28DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7777AR | 制造商:Analog Devices 功能描述:ADC Single SAR 378ksps 10-bit Parallel 28-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:4 CH 10-BIT ADC IC - Bulk |
| AD7777AR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 378ksps 10-bit Parallel 28-Pin SOIC W T/R |
| AD7777ARZ | 功能描述:IC ADC 10BIT 4CH HS 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7777ARZ-REEL | 功能描述:IC ADC 10BIT 4CHAN HS 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。