- 您現在的位置：買賣IC網 > PDF目錄373920 > AD7854L* (Analog Devices, Inc.) 3.3V/5V Low Power RS232 3-Driver/5-Receiver Transceiver; Package: SSOP; No of Pins: 28; Temperature Range: 0°C to +70°C PDF資料下載
參數資料
| 型號： | AD7854L* |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 3.3V/5V Low Power RS232 3-Driver/5-Receiver Transceiver; Package: SSOP; No of Pins: 28; Temperature Range: 0°C to +70°C |
| 中文描述： | 3 V至5 V單電源。 200 kSPS的12位采樣ADC |
| 文件頁數： | 17/28頁 |
| 文件大小： | 264K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7854/AD7854L
REV. B
–
17
–
POWER-UP TIMES
Using an External Reference
When the AD7854/AD7854L are powered up, the parts are
powered up from one of two conditions. First, when the power
supplies are initially powered up and, secondly, when the parts
are powered up from a software power-down (see last section).
When AV
DD
and DV
DD
are powered up, the AD7854/AD7854L
enters a mode whereby the
CONVST
signal initiates a timeout
followed by a self-calibration. The total time taken for this time-
out and calibration is approximately 70 ms
—
see
Calibration on
Power-Up
in the calibration section of this data sheet. The power-
up calibration mode can be disabled if the user writes to the control
register before a
CONVST
signal is applied. If the timeout and
self-calibration are disabled, then the user must take into account
the time required by the AD7854/AD7854L to power up before
a self-calibration is carried out. This power-up time is the time
taken for the AD7854/AD7854L to power up when power is
first applied (300
μ
s typ) or the time it takes the external refer-
ence to settle to the 12-bit level
—
whichever is the longer.
The AD7854/AD7854L powers up from a full software power-
down in 5
μ
s typ. This limits the throughput which the part is
capable of to 100 kSPS for the AD7854 and 60 kSPS for the
AD7854L when powering down between conversions. Figure 21
shows how a full power-down between conversions is implemented
using the
CONVST
pin. The user first selects the power-down
between conversions option by setting the power management
bits, PMGT1 and PMGT0, to 0 and 1 respectively in the control
register (see last section). In this mode the AD7854/AD7854L
automatically enters a full power-down at the end of a conver-
sion, i.e., when BUSY goes low. The falling edge of the next
CONVST
pulse causes the part to power up. Assuming the
external reference is left powered up, the AD7854/AD7854L
should be ready for normal operation 5
μ
s after this falling edge.
The rising edge of
CONVST
initiates a conversion so the
CONVST
pulse should be at least 5
μ
s wide. The part auto-
matically powers down on completion of the conversion. Where
the software convert start is used, the part may be powered up in
software before a conversion is initiated.
t
CONVERT
5 s
4.6 s
POWER-UP
TIME
NORMAL
OPERATION
FULL
POWER-DOWN
POWER-UP
TIME
POWER-UP ON FALLING EDGE
START CONVERSION ON RISING EDGE
BUSY
CONVST
Figure 21. Using the
CONVST
Pin to Power Up the AD7854
for a Conversion
INPUT FREQUENCY
–
kHz
–
78
–
80
–
900
100
20
P
–
40
60
–
82
–
84
–
86
–
88
80
AV
DD
= DV
DD
= 3.3V/5.0V,
100mV pk-pk SINE WAVE ON AV
DD
3.3V
5.0V
Figure 20. PSRR vs. Frequency
POWER-DOWN OPTIONS
The AD7854/AD7854L provides flexible power management to
allow the user to achieve the best power performance for a given
throughput rate. The power management options are selected
by programming the power management bits, PMGT1 and
PMGT0, in the control register. Table VI summarizes the power-
down options that are available and how they can be selected by
programming the power management bits in the control register.
The AD7854/AD7854L can be fully or partially powered down.
When fully powered down, all the on-chip circuitry is powered
down and I
DD
is 10
μ
A typ. If a partial power-down is selected,
then all the on-chip circuitry except the reference is powered
down and I
DD
is 400
μ
A typ with the external clock running.
Additional power savings may be made if the external clock is off.
The choice of full or partial power-down does not give any
significant improvement in the throughput rate which can be
achieved with a power-down between conversions. This is dis-
cussed in the next section
—
Power-Up Times
. But a partial
power-down does allow the on-chip reference to be used exter-
nally even though the rest of the AD7854/AD7854L circuitry is
powered down. It also allows the AD7854/AD7854L to be pow-
ered up faster after a long power-down period when using the
on-chip reference (See
Power-Up Times
section
—
Using the
Internal (On-Chip) Reference
).
As can be seen from Table VI, the AD7854/AD7854L can be
programmed for normal operation, a full power-down at the end
of a conversion, a partial power-down at the end of a conversion
and finally a full power-down whether converting or not. The
full and partial power-down at the end of a conversion can be
used to achieve a superior power performance at slower through-
put rates, in the order of 50 kSPS (see
Power vs. Throughput Rate
section of this data sheet).
Table VI. Power Management Options
PMGT1 PMGT0
Bit
Bit
Comment
0
0
1
1
0
1
0
1
Normal Operation
Full Power-Down After a Conversion
Full Power-Down
Partial Power-Down After a Conversion
相關PDF資料 |
PDF描述 |
|---|---|
| AD7854BR | 3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs |
| AD7854AR | 3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs |
| AD7854L | 12-Bit Sampling ADC(單電源,200kSPS 12位采樣A/D轉換器) |
| AD7854 | 12-Bit Sampling ADC(單電源,200kSPS 12位采樣A/D轉換器) |
| AD7858LARS | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7854LAQ | 制造商:Rochester Electronics LLC 功能描述:12 BIT SINGLE CHANNEL PARALLEL ADC I.C. - Bulk |
| AD7854LAR | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:12-BIT SINGLE CHANNEL PARALLEL ADC I.C. - Bulk |
| AD7854LAR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 12-BIT PARALLEL 28SOIC W - Tape and Reel |
| AD7854LARS | 功能描述:IC ADC 12BIT PARALLEL LP 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
發布緊急采購，3分鐘左右您將得到回復。