- 您現在的位置：買賣IC網 > PDF目錄373920 > AD7858LBN (ANALOG DEVICES INC) 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC PDF資料下載
參數資料
| 型號： | AD7858LBN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| 中文描述： | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP24 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-24 |
| 文件頁數： | 7/32頁 |
| 文件大小： | 315K |
| 代理商： | AD7858LBN |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7858/AD7858L
REV. B
–7–
PIN FUNCTION DESCRIPTIONS
Pin
Mnemonic
Description
1
CONVST
Convert Start. Logic Input. A low to high transition on this input puts the track/hold into its hold mode
and starts conversion. When this input is not used, it should be tied to DV
DD
.
Busy Output. The busy output is triggered high by the falling edge of
CONVST
or rising edge of
CAL
,
and remains high until conversion is completed. BUSY is also used to indicate when the AD7858/
AD7858L has completed its on-chip calibration sequence.
Sleep Input/Low-Power Mode. A Logic 0 initiates a sleep, and all circuitry is powered down including the
internal voltage reference provided there is no conversion or calibration being performed. Calibration
data is retained. A Logic 1 results in normal operation. See Power-Down section for more details.
Reference Input/Output. This pin is connected to the internal reference through a series resistor and is
the reference source for the analog-to-digital converter. The nominal reference voltage is 2.5 V and this
appears at the pin. This pin can be overdriven by an external reference or can be taken as high as AV
DD
.
When this pin is tied to AV
DD,
or when an externally applied reference approaches AV
DD
, the C
REF1
pin
should also be tied to AV
DD
.
Analog Positive Supply Voltage, +3.0 V to +5.5 V.
Analog Ground. Ground reference for track/hold, reference, and DAC.
Reference Capacitor (0.1
μ
F Multilayer Ceramic). This external capacitor is used as a charge source for
the internal DAC. The capacitor should be tied between the pin and AGND.
Reference Capacitor (0.01
μ
F Ceramic Disc). This external capacitor is used in conjunction with the on-
chip reference. The capacitor should be tied between the pin and AGND.
Analog Inputs. Eight analog inputs that can be used as eight single-ended inputs (referenced to AGND)
or four pseudo-differential inputs. Channel configuration is selected by writing to the control register.
Both the positive and negative inputs cannot go below AGND or above AV
DD
at any time. Also the posi-
tive input cannot go below the negative input. See Table III for channel selection.
Calibration Input. This pin has an internal pull-up current source of 0.15
μ
A. A Logic 0 on this pin resets
all calibration control logic and initiates a calibration on its rising edge. There is the option of connecting
a 10 nF capacitor from this pin to DGND to allow for an automatic self-calibration on power-up. This
input overrides all other internal operations. If the autocalibration is not required, this pin should be tied
to a logic high.
Digital Supply Voltage, +3.0 V to +5.5 V.
Digital Ground. Ground reference point for digital circuitry.
Serial Data Output. The data output is supplied to this pin as a 16-bit serial word.
Serial Data Input. The data to be written is applied to this pin in serial form (16-bit word). This pin can
act as an input pin or as a I/O pin depending on the serial interface mode the part is in (see Table X).
Master clock signal for the device (4 MHz AD7858, 1.8 MHz AD7858L). Sets the conversion and cali-
bration times.
Serial Port Clock. Logic Input. The user must provide a serial clock on this input.
Frame Sync. Logic Input. This pin is level triggered active low and frames the serial clock for the read
and write operations (see Table IX).
2
BUSY
3
SLEEP
4
REF
IN
/REF
OUT
5
6
7
AV
DD
AGND
C
REF1
8
C
REF2
9–16 AIN1–AIN8
17
CAL
18
19
20
21
DV
DD
DGND
DOUT
DIN
22
CLKIN
23
24
SCLK
SYNC
相關PDF資料 |
PDF描述 |
|---|---|
| AD7858LBR | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| AD7858L* | 3 V to 5 V Single Supply. 200 kSPS 8-Channel. 12-Bit Sampling ADC |
| AD7862AR-2 | Simultaneous Sampling Dual 250 kSPS 12-Bit ADC |
| AD7862SQ-10 | Simultaneous Sampling Dual 250 kSPS 12-Bit ADC |
| AD7862AR-3 | Simultaneous Sampling Dual 250 kSPS 12-Bit ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7858LBN3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| AD7858LBNZ | 功能描述:IC ADC 12BIT 8CHAN SRL 24DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7858LBR | 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 12-BIT SERL 24SOIC W - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:SELF CAL SERIAL 8 CH. 12 BIT ADC I.C. - Bulk |
| AD7858LBR3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| AD7858LBR-REEL | 功能描述:IC ADC 12BIT 8CH SRL 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。