欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7891YP-1
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: CAT5E PATCH CORD 6 FOOT BEIGE
中文描述: 8-CH 12-BIT PROPRIETARY METHOD ADC, SERIAL/PARALLEL ACCESS, PQCC44
封裝: PLASTIC, MO-047AC, LCC-44
文件頁數: 6/20頁
文件大小: 173K
代理商: AD7891YP-1
AD7891
–6–
REV. A
TERMINOLOGY
Signal to (Noise + Distortion) Ratio
This is the measured ratio of signal to (noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (f
S
/2), excluding dc.
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the quan-
tization noise. The theoretical signal to (noise +distortion) ratio
for an ideal N-bit converter with a sine wave input is given by:
Signal to (Noise + Distortion) = (6.02N + 1.76) dB
Thus for a 12-bit converter, this is 74dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7891 it is defined as:
THD dB
V
V
V
V
V
V
)
=
+
+
+
+
20
2
2
3
2
4
2
5
2
6
2
1
log
where
V
1
is the rms amplitude of the fundamental and
V
2
,
V
3
,
V
4
,
V
5
and V
6
are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to f
S
/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is deter-
mined by the largest harmonic in the spectrum, but for parts
where the harmonics are buried in the noise floor, it will be a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa
±
nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation terms are those for which
neither m nor n are equal to zero. For example, the second
order terms include (fa + fb) and (fa – fb), while the third order
terms include (2fa + fb), (2fa – fb), (fa + 2fb) and (fa – 2fb).
The AD7891 is tested using the CCIF standard where two
input frequencies near the top end of the input bandwidth are
used. In this case, the second and third order terms are of differ-
ent significance. The second order terms are usually distanced
in frequency from the original sine waves while the third order
terms are usually at a frequency close to the input frequencies.
As a result, the second and third order terms are specified sepa-
rately. The calculation of the intermodulation distortion is as
per the THD specification where it is the ratio of the rms sum of
the individual distortion products to the rms amplitude of the
fundamental expressed in dBs.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of
crosstalk between channels. It is measured by applying a full-
scale 20 kHz (AD7891-1) or 100 kHz (AD7891-2) sine wave
signal to one input channel and determining how much that
signal is attenuated in each of the other channels. The figure
given is the worst case across all eight channels.
Relative Accuracy
Relative accuracy or endpoint nonlinearity is the maximum
deviation from a straight line passing through the endpoints of
the ADC transfer function.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Positive Full-Scale Error (AD7891-1,
±
10 V and
±
5 V,
AD7891-2,
±
2.5 V)
This is the deviation of the last code transition (01. . .110 to
01. . .111) from the ideal 4
×
REF IN – 3/2 LSB (AD7891-1
±
10 V range), 2
×
REF IN – 3/2 LSB (AD7891-1
±
5 V range)
or REF IN – 3/2 LSB (AD7891-2,
±
2.5 V range), after the
Bipolar Zero Error has been adjusted out.
Positive Full-Scale Error (AD7891-2, 0 V to 5 V and 0 V to
2.5 V)
This is the deviation of the last code transition (11. . .110 to
11. . .111) from the ideal 2
×
REF IN – 3/2 LSB (0 V to 5 V
range) or REF IN – 3/2 LSB (0 V to 2.5 V range), after the
unipolar offset error has been adjusted out.
Bipolar Zero Error (AD7891-1,
±
10 V and
±
5 V, AD7891-2 ,
±
2.5 V)
This is the deviation of the midscale transition (all 0s to all 1s)
from the ideal AGND – 1/2 LSB.
Unipolar Offset Error (AD7891-2, 0 V to 5 V and 0 V to 2.5 V)
This is the deviation of the first code transition (00. . .000 to
00. . .001) from the ideal AGND + 1/2 LSB.
Negative Full-Scale Error (AD7891-1,
±
10 V and
±
5 V,
AD7891-2,
±
2.5 V)
This is the deviation of the first code transition (10. . .000 to
10. . .001) from the ideal –4
×
REF IN + 1/2 LSB (AD7891-1
±
10 V range), –2
×
REF IN + 1/2 LSB (AD7891-1
±
5 V range)
or –REF IN + 1/2 LSB (AD7891-2,
±
2.5 V range), after Bipolar
Zero Error has been adjusted out.
Track/Hold Acquisition Time
Track/hold acquisition time is the time required for the output
of the track/hold amplifier to reach its final value, within
±
1/2 LSB, after the end of conversion (the point at which the
track/hold returns to track mode). It also applies to situations
where a change in the selected input channel takes place or
where there is a step input change on the input voltage applied
to the selected V
IN
input of the AD7891. It means that the user
must wait for the duration of the track/hold acquisition time
after the end of conversion or after a channel change/step input
change to V
IN
before starting another conversion, to ensure that
the part operates to specification.
相關PDF資料
PDF描述
AD7891AP-1 LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
AD7891AS-1 LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
AD7891BP-1 LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
AD7891BP-2 LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
AD7891BS-1 LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
相關代理商/技術參數
參數描述
AD7891YP-1REEL 制造商:Analog Devices 功能描述:ADC Single 454.5ksps 12-bit Parallel/Serial 44-Pin PLCC T/R 制造商:Analog Devices 功能描述:ADC SGL 454.5KSPS 12-BIT PARALLEL/SERL 44PLCC - Tape and Reel
AD7891YPZ-1 功能描述:IC DAS 12BIT 8CH 44-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7891YPZ-1REEL 功能描述:IC DAS 12BIT 8CH 44-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7891YS1 制造商:AD 功能描述:New
AD7891YS-1 制造商:Analog Devices 功能描述:ADC Single 454.5ksps 12-bit Parallel/Serial 44-Pin MQFP
主站蜘蛛池模板: 凌云县| 长乐市| 绥棱县| 乌拉特中旗| 嘉义市| 吴堡县| 即墨市| 承德县| 德庆县| 临沭县| 新乡县| 阳春市| 侯马市| 偃师市| 格尔木市| 富平县| 保康县| 绥阳县| 宜良县| 班玛县| 舟曲县| 大余县| 盐城市| 定边县| 开江县| 渭南市| 苏尼特左旗| 阿鲁科尔沁旗| 河津市| 丰城市| 中方县| 玛多县| 察隅县| 新竹市| 鸡西市| 乡宁县| 高台县| 陇川县| 安多县| 墨脱县| 瑞安市|