- 您現在的位置：買賣IC網 > PDF目錄373939 > AD815 (Analog Devices, Inc.) High Output Current Differential Driver(高輸出電流差分驅動器) PDF資料下載
參數資料
| 型號： | AD815 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | High Output Current Differential Driver(高輸出電流差分驅動器) |
| 中文描述： | 高輸出電流差動驅動器（高輸出電流差分驅動器） |
| 文件頁數： | 13/16頁 |
| 文件大小： | 320K |
| 代理商： | AD815 |
AD815
REV. A
–13–
6
4
5
8
+15V
10
7
–15V
R
F
499
R
L
9
11
0.1μF
10μF
R
G
100
R
F
499
0.1μF
10μF
1/2
AD815
1
8
+15V
0.1μF
2
1k
4
–15V
1k
7
0.1μF
6
5
1k
3
1/2
AD815
1/2
1/2
100
100
1k
Figure 50. Differential Driver with Single-Ended
Differential Converter
Another means for creating a differential signal from a single-
ended signal is to use a transformer with a center-tapped
secondary. T he center tap of the transformer is grounded and
the two secondary windings are connected to obtain opposite
polarity signals to the two inputs of the AD815 amplifiers. T he
bias currents for the AD815 inputs are provided by the center
tap ground connection through the transformer windings.
One advantage of using a transformer is its ability to provide
isolation between circuit sections and to provide good common-
mode rejection. T he disadvantages are that transformers have
no dc response and can sometimes be large, heavy and expensive.
T his circuit is shown in Figure 51.
6
4
5
8
+15V
10
7
–15V
R
L
9
11
0.1μF
10μF
200
0.1μF
10μF
1/2
AD815
1k
1k
1/2
AD815
50
100
100
50
Figure 51. Differential Driver with Transformer Input
Direct Single-E nded to Differential Conversion
T wo types of circuits can create a differential output signal from
a single-ended input without the use of any other components
other than resistors. T he first of these is illustrated in Figure 52.
6
4
5
8
+15V
10
7
–15V
R
F1
402
R
L
9
11
R
G
100
R
F2
499
1/2
AD815
1/2
AD815
V
IN
V
OUT
AMP 1
AMP 2
Figure 52. Direct Single-Ended to Differential Conversion
Amp 1 has its + input driven with the input signal, while the +
input of Amp 2 is grounded. T hus the – input of Amp 2 is
driven to virtual ground potential by its output. T herefore
Amp 1 is configured for a noninverting gain of five, (1 + R
F1
/R
G
),
because R
G
is connected to the virtual ground of Amp 2’s – input.
When the + input of Amp 1 is driven with a signal, the same
signal appears at the – input of Amp 1. T his signal serves as an
input to Amp 2 configured for a gain of –5, (–R
F2
/R
G
). T hus the
two outputs move in opposite directions with the same gain and
create a balanced differential signal.
T his circuit can work at various gains with proper resistor
selection. But in general, in order to change the gain of the
circuit, at least two resistor values will have to be changed. In
addition, the noise gain of the two op amps in this configuration
will always be different by one, so the bandwidths will not
match.
A second circuit that has none of the disadvantages mentioned
in the above circuit creates a differential output voltage feedback
op amp out of the pair of current feedback op amps in the
AD815. T his circuit, drawn in Figure 53, can be used as a high
power differential line driver, such as required for ADSL
(asymmetrical digital subscriber loop) line driving.
Each of the AD815’s op amps is configured as a unity gain
follower by the feedback resistors (R
A
). Each op amp output
also drives the other as a unity gain inverter via the two R
B
s,
creating a totally symmetrical circuit.
If the + input to Amp 2 is grounded and a small positive signal
is applied to the + input of Amp 1, the output of Amp 1 will be
driven to saturation in the positive direction and the output of
Amp 2 driven to saturation in the negative direction. T his is
similar to the way a conventional op amp behaves without any
feedback.
相關PDF資料 |
PDF描述 |
|---|---|
| AD816 | 500 mA Differential Driver & Dual Low Noise (VF) Amplifiers(500mA差分驅動器和雙低噪電壓反饋放大器) |
| AD8170AN | 250 MHz, 10 ns Switching Multiplexers w/Amplifier |
| AD8170AR | 250 MHz, 10 ns Switching Multiplexers w/Amplifier |
| AD8170-EB | 250 MHz, 10 ns Switching Multiplexers w/Amplifier |
| AD8170AR-REEL | 250 MHz, 10 ns Switching Multiplexers w/Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD815_05 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Output Current Differential Driver |
| AD8150 | 制造商:AD 制造商全稱:Analog Devices 功能描述:33 x 17, 1.5 Gbps Digital Crosspoint Switch |
| AD8150AST | 制造商:Rochester Electronics LLC 功能描述:LQFP 1.5GBPS 33X17 DIGITAL CROSSPOINT SW - Tape and Reel 制造商:Analog Devices 功能描述:IC SWITCH CROSSPOINT |
| AD8150ASTZ | 功能描述:IC CROSSPOINT SWIT 33X17 184LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:XStream™ 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| AD8150ASTZ | 制造商:Analog Devices 功能描述:IC DIGITAL CROSSPOINT SWITCH |
發布緊急采購，3分鐘左右您將得到回復。