- 您現在的位置：買賣IC網 > PDF目錄373939 > AD8178-EVALZ1 (Analog Devices, Inc.) 450 MHz, Triple 16 】 5 Video Crosspoint Switch PDF資料下載
參數資料
| 型號： | AD8178-EVALZ1 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 450 MHz, Triple 16 】 5 Video Crosspoint Switch |
| 中文描述： | 450兆赫，三16】5視頻交叉點開關 |
| 文件頁數： | 27/40頁 |
| 文件大小： | 545K |
| 代理商： | AD8178-EVALZ1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD8178
APPLICATIONS INFORMATION
OPERATING MODES
Depending on the state of the CMENC logic input, the AD8178
can be set in either of two differential-in, differential-out operat-
ing modes. In addition, monitors can be driven directly by tapping
the outputs single-ended and making use of the decoded H and
V sync outputs.
Middle-of-Cat-5-Run Application, CM Encoding Turned Off
In this application, the AD8178 is placed somewhere in the middle
of a Cat-5 run. By tying CMENC low, the CM of each RGB differ-
ential pair is removed through the device (or turned off), and
the overall CM at the output is defined by the reference value
VOCM_CMENCOFF. In this mode of operation, CM noise is
removed, while the intended differential RGB signals are buffered
and passed to the outputs. The AD8178 is placed in this operation
mode when used in a sync-on color scheme. Figure 46 shows
the voltage levels and CM handling for a single input channel
connected to a single output channel in a middle-of-Cat-5-run
application with CM encoding turned off.
Rev. 0 | Page 27 of 40
CM
R
CM
B
DIFF. R
DIFF. B
INPUT
CM
G
DIFF. G
CMENC
AD8178
CM
R
CM
B
DIFF. R
DIFF. B
OUTPUT
CM
G
DIFF. G
VOCM_CMENCOFF
0
Figure 46. AD8178 in a Middle-of-Cat-5-Run Application, CM Encoding Off
(Note that in this application, the H and V outputs, though asserted, are not used.)
Input VBLK and Input VOCM_CMENCOFF allow the user
complete flexibility in defining the output CM level and the
amount of overlap between the positive and negative phases,
thus maximizing output headroom usage. Whenever VBLK
differs from VOCM_CMENCOFF by more than ±100 mV,
a differential voltage, Δ
diff
, is added at the outputs according
to the expression Δ
diff
= 2
×
(VBLK VOCM_CMENCOFF.)
Conversely, whenever the difference between VBLK and
VOCM_CMENCOFF is less than ±100 mV, no differential
voltage is added at the outputs.
Middle-of-Cat-5-Run Application, CM Encoding Turned On
In this application, the AD8178 is also placed somewhere in the
middle of a Cat-5 run, although the common-mode handling is
different. By tying CMENC high, the CM of each RGB input is
passed through the part with a gain of +1, while at the same time,
the overall output CM is stripped and set equal to the voltage
applied at the VOCM_CMENCON pin. The AD8178 is placed in
this operation mode when used with a sync-on CM scheme.
Although asserted, the H and V outputs are not used in this
application.
Figure 47 shows the voltage levels and CM handling for a single
input channel connected to a single output channel in a middle-
of-Cat-5-run application with CM encoding turned on.
CM
R
CM
B
DIFF. R
DIFF. B
INPUT
CM
G
DIFF. G
CMENC
AD8178
CM
R
CM
B
DIFF. R
DIFF. B
OUTPUT
CM
G
DIFF. G
VOCM_CMENCON
0
Figure 47. AD8178 in Middle-of-Cat-5-Run Application, CM Encoding On
(Note that in this application, the H and V outputs, though asserted, are not used.)
In this operation mode, the difference Δ
diff
= 2
×
(VBLK
VOCM_CMENCOFF) still adds an output differential voltage,
as described in the Middle-of-Cat-5-Run Application, CM
Encoding Turned Off section.
End-of-Cat-5-Run Application, CM Encoding Turned Off—
Driving a Monitor Directly
In this application, the AD8178 is placed at the end of a Cat-5
run to drive a monitor directly: the differential outputs are
tapped single-ended to drive the monitor inputs, CMENC is
tied to logic low to remove sync-on-CM information at the
output of the part, and the decoded H and V sync outputs are
tied to the sync inputs of the monitor.
The differential-in, differential-out gain of +4 provides a
differential-in, single-ended out gain of +2 at the output pins of
the AD8178. This yields the correct differential-in, single-ended
out gain of +1 at the input of the monitor.
The relationship between the incoming sync-on CM signaling
and the H and V syncs is defined according to Table 16.
Table 16. H and V Sync Truth Table (V
POS
/V
NEG
= ±2.5 V)
CM
R
CM
G
CM
B
0.5
0
0
0
0.5
0.5
0.5
0.5
0
0
0.5
0.5
H
Low
Low
High
High
V
High
Low
Low
High
The following two statements are equivalent to the truth table
(Table 16) in producing H and V for all allowable CM inputs:
H sync is high when the CM of Blue is larger than the CM
of Red.
V sync is high when the combined CM of Red and Blue is
larger than the CM of Green.
相關PDF資料 |
PDF描述 |
|---|---|
| AD817 | High Speed, Low Power Wide Supply Range Amplifier(高速,低功耗,寬電源范圍放大器) |
| AD8180-EB | 750 MHz, 3.8 mA 10 ns Switching Multiplexers |
| AD8180AN | 750 MHz, 3.8 mA 10 ns Switching Multiplexers |
| AD8180AR | 750 MHz, 3.8 mA 10 ns Switching Multiplexers |
| AD8180AR-REEL | 750 MHz, 3.8 mA 10 ns Switching Multiplexers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD817AN | 功能描述:IC OPAMP HS LP 8-DIP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| AD817AN | 制造商:Analog Devices 功能描述:SEMICONDUCTORSLINEAR |
| AD817ANZ | 功能描述:IC OPAMP HS LP 8-DIP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| AD817AR | 功能描述:IC OPAMP HS LP 8-SOIC RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| AD817AR-EBZ | 功能描述:BOARD EVAL FOR AD817AR RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。