
REV. 0
AD8302
–4–
ABSOLUTE MAXIMUM RATINGS
1
Supply Voltage V
S
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
PSET, MSET Voltage . . . . . . . . . . . . . . . . . . . . . . V
S
+ 0.3 V
INPA, INPB Maximum Input . . . . . . . . . . . . . . . . . . –3 dBV
Equivalent Power Re. 50
. . . . . . . . . . . . . . . . . . 10 dBm
θ
JA2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
°
C/W
Maximum Junction Temperature . . . . . . . . . . . . . . . . 125
°
C
Operating Temperature Range . . . . . . . . . . . –40
°
C to +85
°
C
Storage Temperature Range . . . . . . . . . . . . –65
°
C to +150
°
C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . 300
°
C
NOTES
Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
JEDEC 1S Standard (2-layer) board data.
PIN CONFIGURATION
TOP VIEW
(Not to Scale)
1
COMM
AD8302
INPA
OFSA
VPOS
OFSB
INPB
COMM
MFLT
VMAG
MSET
VREF
PSET
VPHS
PFLT
2
3
4
5
6
7
14
13
12
11
10
9
8
PIN FUNCTION DESCRIPTIONS
Equivalent
Circuit
Pin No.
Mnemonic
Function
1, 7
2
3
COMM
INPA
OFSA
Device Common. Connect to low impedance ground.
High Input Impedance to Channel A. Must be ac-coupled.
A capacitor to ground at this pin sets the offset compensation filter corner
and provides input decoupling.
Voltage Supply (V
S
), 2.7 V to 5.5 V.
A capacitor to ground at this pin sets the offset compensation filter corner
and provides input decoupling.
Input to Channel B. Same structure as INPA.
Low-Pass Filter Terminal for the Phase Output.
Single-Ended Output Proportional to the Phase Difference between INPA
and INPB.
Feedback Pin for Scaling of VPHS Output Voltage in Measurement Mode.
Apply a setpoint voltage for controller mode.
Internally-Generated Reference Voltage (1.8 V Nominal).
Feedback Pin for Scaling of VMAG Output Voltage Measurement Mode.
Accepts a set point voltage in controller mode.
Single-Ended Output. Output voltage proportional to the decibel ratio
of signals applied to INPA and INPB.
Low-Pass Filter Terminal for the Magnitude Output.
Circuit A
Circuit A
4
5
VPOS
OFSB
Circuit A
6
8
9
INPB
PFLT
VPHS
Circuit A
Circuit E
Circuit B
10
PSET
Circuit D
11
12
VREF
MSET
Circuit C
Circuit D
13
VMAG
Circuit B
Circuit E
14
MFLT
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD8302 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
ORDERING GUIDE
Package
Option
Model
Temperature Range
–40
°
C to +85
°
C
Package Description
AD8302ARU
AD8302ARU-REEL
AD8302ARU-REEL7
AD8302-EVAL
Tube, 14-Lead TSSOP
13" Tape and Reel
7" Tape and Reel
Evaluation Board
RU-14