- 您現在的位置：買賣IC網 > PDF目錄373965 > AD9708ARU (ANALOG DEVICES INC) 8-Bit, 100 MSPS TxDAC D/A Converter PDF資料下載
參數資料
| 型號： | AD9708ARU |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | 8-Bit, 100 MSPS TxDAC D/A Converter |
| 中文描述： | PARALLEL, 8 BITS INPUT LOADING, 0.035 us SETTLING TIME, 8-BIT DAC, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 246K |
| 代理商： | AD9708ARU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁
AD9708
–11–
REV. B
should be considered. The necessity and value of this resistor
will be dependent upon the logic family used.
For a more detailed discussion of the implementation and
construction of high speed, mixed signal printed circuit boards,
refer to Analog Devices’ application notes AN-280 and AN-333.
DIFFERENTIAL OUTPUT CONFIGURATIONS
For applications requiring the optimum dynamic performance
and/or a bipolar output swing, a differential output configura-
tion is suggested. A differential output configuration may con-
sists of either an RF transformer or a differential op amp
configuration. The transformer configuration is well suited for
ac coupling applications. It provides the optimum high fre-
quency performance due to its excellent rejection of common-
mode distortion (i.e., even-order harmonics) and noise over a
wide frequency range. It also provides electrical isolation and
the ability to deliver twice the power to the load (i.e., assuming
no source termination). The differential op amp configuration is
suitable for applications requiring dc coupling, a bipolar output,
signal gain, and/or level shifting.
Figure 23 shows the AD9708 in a typical transformer coupled
output configuration. The center-tap on the primary side of the
transformer must be connected to ACOM to provide the necessary
dc current path for both IOUTA and IOUTB. The complemen-
tary voltages appearing at IOUTA and IOUTB (i.e., V
OUTA
and
V
OUTB
) swing symmetrically around ACOM and should be
maintained within the specified output compliance range of the
AD9708. A differential resistor, R
DIFF
, may be inserted in
applications in which the output of the transformer is connected
to the load, R
LOAD
, via a passive reconstruction filter or cable.
R
DIFF
is determined by the transformer’s impedance ratio and
provides the proper source termination. Note that approxi-
mately half the signal power will be dissipated across R
DIFF
.
R
LOAD
AD9708
22
21
MINI-CIRCUITS
T1-1T
OPTIONAL R
DIFF
IOUTA
IOUTB
Figure 23. Differential Output Using a Transformer
An op amp can also be used to perform a differential to single-
ended conversion as shown in Figure 24. The AD9708 is
configured with two equal load resistors, R
LOAD
, of 25
. The
differential voltage developed across IOUTA and IOUTB is
converted to a single-ended signal via the differential op amp
configuration. An optional capacitor can be installed across
IOUTA and IOUTB forming a real pole in a low-pass filter.
The addition of this capacitor also enhances the op amps distortion
performance by preventing the DACs high slewing output from
overloading the op amp’s input.
AD9708
22
IOUTA
IOUTB
21
C
OPT
500
V
225
V
225
V
500
V
25
V
25
V
AD8072
Figure 24. DC Differential Coupling Using an Op Amp
The common-mode rejection of this configuration is typically
determined by the resistor matching. In this circuit, the differ-
ential op amp circuit is configured to provide some additional
signal gain. The op amp must operate off a dual supply since its
output is approximately
±
1.0 V. A high speed amplifier capable
of preserving the differential performance of the AD9708 while
meeting other system level objectives (i.e., cost, power) should
be selected. The op amps differential gain, its gain setting resis-
tor values and full-scale output swing capabilities should all be
considered when optimizing this circuit.
The differential circuit shown in Figure 25 provides the neces-
sary level-shifting required in a single supply system. In this
case, AVDD, which is the positive analog supply for both the
AD9708 and the op amp, is also used to level-shift the differ-
ential output of the AD9762 to midsupply (i.e., AVDD/2).
AD9708
22
IOUTA
IOUTB
21
C
OPT
500
V
225
V
225
V
1k
V
25
V
25
V
AD8072
1k
V
AVDD
Figure 25. Single-Supply DC Differential Coupled Circuit
AD9708 EVALUATION BOARD
General Description
The AD9708-EB is an evaluation board for the AD9708 8-bit
D/A converter. Careful attention to layout and circuit design,
combined with a prototyping area, allows the user to easily and
effectively evaluate the AD9708 in any application where high
resolution, high speed conversion is required.
This board allows the user the flexibility to operate the AD9708
in various configurations. Possible output configurations include
transformer coupled, resistor terminated, inverting/noninverting
and differential amplifier outputs. The digital inputs are
designed to be driven directly from various word generators,
with the on-board option to add a resistor network for proper
load termination. Provisions are also made to operate the
AD9708 with either the internal or external reference, or to
exercise the power-down feature.
Refer to the application note AN-420 “Using the AD9760/
AD9762/AD9764-EB Evaluation Board” for a thorough
description and operating instructions for the AD9708 evalua-
tion board.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9708* | 1A Low Noise High Current LED Charge Pump with Independent Torch/Flash Current Control; Package: DFN; No of Pins: 12; Temperature Range: -40°C to +125°C |
| AD9708 | 8-Bit, 100 MSPS TxDAC D/A Converter |
| AD9709 | 8-Bit, 125 MSPS Dual TxDAC D/A Converter |
| AD9709AST | RES 0.01 OHM MAX 25 AMP AXIAL |
| AD9709-EB | 8-Bit, 125 MSPS Dual TxDAC D/A Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9708ARURL | 功能描述:INTEGRATED CIRCUIT 制造商:analog devices inc. 系列:* 包裝:帶卷（TR） 零件狀態:最後搶購 封裝/外殼:28-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:28-TSSOP 標準包裝:1 |
| AD9708ARURL7 | 功能描述:IC DAC 8BIT 100MSPS 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD9708ARUZ | 功能描述:IC DAC 8BIT 100MSPS 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD9708ARUZ | 制造商:Analog Devices 功能描述:IC, DAC, 8BIT, 125MSPS, TSSOP-28 |
| AD9708ARUZRL7 | 功能描述:IC DAC 8BIT 100MSPS 28-TSSOP TR RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。