- 您現在的位置：買賣IC網 > PDF目錄373965 > AD9708ARU (ANALOG DEVICES INC) 8-Bit, 100 MSPS TxDAC D/A Converter PDF資料下載
參數資料
| 型號： | AD9708ARU |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | 8-Bit, 100 MSPS TxDAC D/A Converter |
| 中文描述： | PARALLEL, 8 BITS INPUT LOADING, 0.035 us SETTLING TIME, 8-BIT DAC, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 7/16頁 |
| 文件大小： | 246K |
| 代理商： | AD9708ARU |
AD9708
–7–
REV. B
FUNCTIONAL DESCRIPTION
Figure 12 shows a simplified block diagram of the AD9708. The
AD9708 consists of a large PMOS current source array capable of
providing up to 20 mA of total current. The array is divided into
31 equal currents that make up the five most significant bits
(MSBs). The remaining 3 LSBs are also implemented with equally
weighted current sources whose sum total equals 7/8th of an
MSB current source. Implementing the upper and lower bits
with current sources helps maintain the DAC’s high output
impedance (i.e. > 100 k
). All of these current sources are
switched to one or the other of the two output nodes (i.e., IOUTA
or IOUTB) via PMOS differential current switches. The switches
are based on a new architecture that drastically improves
distortion performance.
The analog and digital sections of the AD9708 have separate
power supply inputs (i.e., AVDD and DVDD) that can operate
independently over a 2.7 volt to 5.5 volt range. The digital section,
which is capable of operating up to a 125 MSPS clock rate,
consists of edge-triggered latches and segment decoding logic
circuitry. The analog section includes the PMOS current
sources, the associated differential switches, a 1.20 V bandgap
voltage reference and a reference control amplifier.
The full-scale output current is regulated by the reference con-
trol amplifier and can be set from 2 mA to 20 mA via an exter-
nal resistor, R
SET
. The external resistor, in combination with
both the reference control amplifier and voltage reference
V
REFIO
, sets the reference current I
REF
, which is mirrored over to
the segmented current sources with the proper scaling factor.
The full-scale current, I
OUTFS
, is thirty-two times the value of I
REF
.
DAC TRANSFER FUNCTION
The AD9708 provides complementary current outputs, IOUTA
and IOUTB. IOUTA will provide a near full-scale current output,
I
OUTFS
, when all bits are high (i.e., DAC CODE = 255), while
IOUTB, the complementary output, provides no current. The
current output appearing at IOUTA and IOUTB are a function
of both the input code and I
OUTFS
and can be expressed as:
I
OUTA
= (
DAC CODE
/256)
×
I
OUTFS
I
OUTB
= (255 –
DAC CODE
)/256
×
I
OUTFS
where
DAC CODE
= 0 to 255 (i.e., Decimal Representation).
(1)
(2)
As previously mentioned, I
OUTFS
is a function of the reference
current I
REF
, which is nominally set by a reference voltage
V
REFIO
and external resistor R
SET
. It can be expressed as:
I
OUTFS
= 32
×
I
REF
where
I
REF
=
V
REFIO
/
R
SET
The two current outputs will typically drive a resistive load
directly. If dc coupling is required, IOUTA and IOUTB should
be directly connected to matching resistive loads, R
LOAD
, which
are tied to analog common, ACOM. Note, R
LOAD
may repre-
sent the equivalent load resistance seen by IOUTA or IOUTB
as would be the case in a doubly terminated 50
or 75
cable.
The single-ended voltage output appearing at the IOUTA and
IOUTB nodes is simply:
V
OUTA
=
I
OUTA
×
R
LOAD
V
OUTB
=
I
OUTB
×
R
LOAD
Note the full-scale value of V
OUTA
and V
OUTB
should not exceed
the specified output compliance range to maintain specified
distortion and linearity performance.
The differential voltage, V
DIFF
, appearing across IOUTA and
IOUTB is:
V
DIFF
= (
I
OUTA
– I
OUTB
)
×
R
LOAD
Substituting the values of I
OUTA
, I
OUTB
, and I
REF
; V
DIFF
can be
expressed as:
V
DIFF
= {(2
DAC CODE
– 255)/256}/
×
(32
R
LOAD
/
R
SET
)
×
V
REFIO
(3)
(4)
(5)
(6)
(7)
(8)
VOLTAGE REFERENCE AND CONTROL AMPLIFIER
The AD9708 contains an internal 1.20 V bandgap reference
that can be easily disabled and overridden by an external refer-
ence. REFIO serves as either an
input
or
output
depending on
whether the internal or an external reference is selected. If
REFLO is tied to ACOM, as shown in Figure 13, the internal
reference is activated and REFIO provides a 1.20 V output. In
this case, the internal reference
must
be compensated externally
with a ceramic chip capacitor of 0.1
μ
F or greater from REFIO
to REFLO. Note that REFIO is not designed to drive any ex-
ternal load. It should be buffered with an external amplifier
having an input bias current less than 100 nA if any additional
loading is required.
+1.20V REF
REFLO
REFIO
FS ADJ
50pF
COMP1
0.1
m
F
CURRENT
SOURCE
ARRAY
+5V
AVDD
SEGMENTED
SWITCHES
LATCHES
DVDD
DCOM
CLOCK
SLEEP
IOUTA
IOUTB
COMP2
ACOM
0.1
m
F
+5V
R
SET
2k
V
0.1
m
F
AD9708
I
OUTB
V
OUTB
R
LOAD
50
V
V
OUTA
R
LOAD
50
V
I
OUTA
V
DIFF
= V
OUTA
– V
OUTB
CLOCK
I
REF
V
REFIO
DIGITAL DATA INPUTS (DB7–DB0)
Figure 12. Functional Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AD9708* | 1A Low Noise High Current LED Charge Pump with Independent Torch/Flash Current Control; Package: DFN; No of Pins: 12; Temperature Range: -40°C to +125°C |
| AD9708 | 8-Bit, 100 MSPS TxDAC D/A Converter |
| AD9709 | 8-Bit, 125 MSPS Dual TxDAC D/A Converter |
| AD9709AST | RES 0.01 OHM MAX 25 AMP AXIAL |
| AD9709-EB | 8-Bit, 125 MSPS Dual TxDAC D/A Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9708ARURL | 功能描述:INTEGRATED CIRCUIT 制造商:analog devices inc. 系列:* 包裝:帶卷（TR） 零件狀態:最後搶購 封裝/外殼:28-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:28-TSSOP 標準包裝:1 |
| AD9708ARURL7 | 功能描述:IC DAC 8BIT 100MSPS 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD9708ARUZ | 功能描述:IC DAC 8BIT 100MSPS 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD9708ARUZ | 制造商:Analog Devices 功能描述:IC, DAC, 8BIT, 125MSPS, TSSOP-28 |
| AD9708ARUZRL7 | 功能描述:IC DAC 8BIT 100MSPS 28-TSSOP TR RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。