欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD9862PCB
廠商: Analog Devices, Inc.
英文描述: Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications
中文描述: 混合寬帶通信信號前端(MxFE⑩)處理器
文件頁數: 20/32頁
文件大?。?/td> 617K
代理商: AD9862PCB
REV. 0
–20–
AD9860/AD9862
The second interpolation filter will provide an additional 2 inter-
polation for an overall 4 interpolation. The second filter is a
15 tap filter. It suppresses out-of-band signals by 60 dB or more.
The flat passband response (less than 0.1 dB attenuation) is 38%
of the Tx input data rate (9.5% of f
DAC
). The maximum input
data rate per channel is 32 MSPS per channel when using
4
interpolation.
The 2 and 4 Interpolation Filter Transfer function plots are
shown in Figure 4a and 4b, respectively.
NORMALIZED –
f
S
10
0
M
0
–10
–20
–30
–40
–50
–60
–70
–80
–100
0.1
–90
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
INTERPOLATION
FILTER
INCLUDUNG SIN (X)/X
NORMALIZED –
f
S
10
0
M
0
–10
–20
–30
–40
–50
–60
–70
–80
–100
0.1
–90
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
INTERPOLATION
FILTER
INCLUDUNG SIN (X)/X
Figure 4. Spectral Response of 2 Interpolation Filter
(top) and 4 Interpolation Filter (bottom)
Fine Modulation Stage
A digital fine modulation stage is available in the transmit path to
shift the complex Tx output spectrum using a 24-bit numerically
controlled oscillator (NCO). To utilize the Fine Modulation
Block, 4 interpolation is required. Therefore, the maximum
input date rate is 32 MSPS per channel, which generates a DAC
update rate, f
DAC
, of 128 MSPS. The NCO can tune up to 1/4 of
f
DAC
, providing a step resolution of f
DAC
/2
26
. Since the Fine
Modulation Stage precedes the Interpolation Filters, care must
be taken to ensure the entire desired signal is placed within the
pass band of the Interpolation Filter.
By default, the Fine Modulation Block is bypassed. To enable it
to perform a complex mix of the Tx I and Q data, Register 2
s data
paths, Fine Mod and Fine, should be configured. The NCO
frequency tuning word is set in the three FTW registers.
Hilbert Filter
The Hilbert filter is available to provide a Hilbert transform of
real
input data at a low intermediate frequency (IF) between
12.5% to 38% of the input data rate. The Hilbert filter essentially
transforms this
real,
single channel input data into a complex
representation (i.e., I and Q components) that can be used as
part of an image rejection architecture. The complex data can than
be processed further using the on-chip digital complex modulators.
The Hilbert filter requires 4 interpolation to be enabled and
accepts data at a maximum 32 MSPS. Figure 5 shows a spectral
plot of the Hilbert filter impulse response.
FREQUENCY – MHz
100
–20
d
80
60
40
20
0
–20
–40
–60
–80
–100
–15
–10
–5
0
5
10
15
20
Figure 5. Tx Hilbert Filter, Keeping Positive
Frequencies Spectral Plot
Latch/Demultiplexer
The AD9860/AD9862 Tx path accepts dual or single channel
data. The dual channel data can represent two independent real
signals or a complex signal. Various input data latching schemes
relative to one of the output clocks, CLKOUT1 or CLKOUT2,
are allowed, including using any combination of rising and falling
clock edges.
Associated Tx timing is discussed in detail in the Clock Overview
section of the data sheet.
TRANSMIT APPLICATIONS SECTION
The AD9860/AD9862 transmit path (Tx) includes two, high speed,
high performance, 12-/14-bit TxDACs. Figure 3 shows a detailed
block diagram of the transmit data path and can be referred to
throughout the explanation of the various modes of operation.
The various Tx modes of operation are broken into three parts,
determined by the format of the input data. They are:
1. Single Channel DAC Data
2. Two Independent Real Signal DAC Data (diversity or dual
channel
3. Dual Channel Complex DAC Data (I and Q or Single Sideband)
Single Channel DAC Data
In this mode, 12-/14-bit single channel Tx data is provided to
the AD9860/AD9862 and latched using either CLKOUT1 or
CLKOUT2 edges as defined in the Clock Overview section of
the data sheet. All Tx digital signal processing blocks can be
utilized to address reconstruction filtering at the DAC output
and aid in frequency tuning.
相關PDF資料
PDF描述
AD9860 Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications
AD9860BST Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications
AD9860PCB Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications
AD9862 Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications
AD9862BST Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications
相關代理商/技術參數
參數描述
AD9863 制造商:AD 制造商全稱:Analog Devices 功能描述:Mixed-Signal Front-End (MxFE⑩) Baseband Transceiver for Broadband Applications
AD9863-50EB 制造商:Analog Devices 功能描述:12 BIT, 50 MSPS MXFE CONVERTER - Bulk
AD9863-50EBZ 制造商:Analog Devices 功能描述:Evaluation Board For Mixed-Signal Front-End Baseband Transceiver For Broadband Applications 制造商:Analog Devices 功能描述:MIXED-SGNL FRONT-END (MXFE) BASEBAND TRNSCVR FOR BROADBAND A - Bulk
AD9863BCP-50 制造商:Analog Devices 功能描述:Mixed Signal Front End 64-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:12 BIT, 50 MSPS MXFE DUAL CONVERTER - Bulk 制造商:Analog Devices 功能描述:12BIT MIXED SIGNAL CONVERTER 9863
AD9863BCPRL-50 制造商:Analog Devices 功能描述:Mixed Signal Front End 64-Pin LFCSP EP T/R
主站蜘蛛池模板: 广昌县| 龙胜| 精河县| 孝感市| 颍上县| 九寨沟县| 收藏| 厦门市| 翼城县| 太白县| 水城县| 固阳县| 铜川市| 永定县| 博罗县| 全州县| 鄯善县| 互助| 昌邑市| 台东市| 昌平区| 磴口县| 宜丰县| 辽宁省| 谷城县| 德阳市| 个旧市| 巴彦淖尔市| 萨嘎县| 黑河市| 莫力| 保德县| 三亚市| 赤水市| 寿宁县| 视频| 贞丰县| 宜章县| 敖汉旗| 玉门市| 赣州市|