- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1026JST (ANALOG DEVICES INC) Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 PDF資料下載
參數資料
| 型號： | ADM1026JST |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026BBC, LQFP-48 |
| 文件頁數： | 14/56頁 |
| 文件大小： | 634K |
| 代理商： | ADM1026JST |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
ADM1026
Bit 3 of EEPROM Register 3 is used for EEPROM write protec-
tion. Setting this bit prevents accidental programming or era-
sure of the EEPROM. If an EEPROM write or erase operation
is attempted when this bit is set, the ADM1026 responds with
No Acknowledge. This bit is write-once and can only be cleared
by a power-on reset.
Rev. A | Page 14 of 56
EEPROM Register 3 Bit 7 is used for clock extend. Program-
ming an EEPROM byte takes approximately 250 μs, which
would limit the SMBus clock for repeated or block write opera-
tions. Because EEPROM block read/write access is slow, it is
recommended that this clock extend bit typically be set to 1.
This allows the ADM1026 to pull SCL low and extend the
clock pulse when it cannot accept any more data.
ADM1026 SMBus Operations
The SMBus specification defines several protocols for different
types of read and write operations. The ones used in the
ADM1026 are discussed below. The following abbreviations are
used in the diagrams:
S
W
P
A
R
A
ADM1026 Write Operations
Send Byte
In this operation, the master device sends a single command
byte to a slave device, as follows:
1.
The master device asserts a start condition on the SDA.
2.
The master sends the 7-bit slave address followed by the
write bit (low).
3.
The addressed slave device asserts an ACK on the SDA.
4.
The master sends a command code.
5.
The slave asserts ACK on the SDA.
6.
The master asserts a stop condition on the SDA and the
transaction ends.
In the ADM1026, the send byte protocol is used to write a
register address to RAM for a subsequent single-byte read from
the same address or block read or write starting at that address.
This is illustrated in Figure 19.
Start
Write
Stop
Acknowledge
Read
No Acknowledge
S
ASLAVE
RAM
ADDRESS
(00h TO 6Fh)
A
A
P
1
2
3
4
5
6
0
Figure 19. Setting a RAM Address for Subsequent Read
If it is required to read data from the RAM immediately after
setting up the address, the master can assert a repeat start
condition immediately after the final ACK and carry out a
single byte read, block read, or block write operation without
asserting an intermediate stop condition.
Write Byte/Word
In this operation, the master device sends a command byte and
one or two data bytes to the slave device as follows:
1.
The master device asserts a start condition on the SDA.
2.
The master sends the 7-bit slave address followed by the
write bit (low).
3.
The addressed slave device asserts an ACK on the SDA.
4.
The master sends a command code.
5.
The slave asserts an ACK on the SDA.
6.
The master sends a data byte.
7.
The slave asserts an ACK on the SDA.
8.
The master sends a data byte (or may assert stop here.)
9.
The slave asserts an ACK on the SDA.
10.
The master asserts a stop condition on the SDA to end the
transaction.
In the ADM1026, the write byte/word protocol is used for four
purposes. The ADM1026 knows how to respond by the value of
the command byte and EEPROM Register 3.
The first purpose is to write a single byte of data to RAM. In
this case, the command byte is the RAM address from 00h to
6Fh and the (only) data byte is the actual data. This is illustrated
in Figure 20.
S
ASLAVE
RAM
ADDRESS
(00h TO 6Fh)
1
2
3
4
5
6
A DATA A P
7
8
0
Figure 20. Single Byte Write to RAM
The protocol is also used to set up a 2-byte EEPROM address
for a subsequent read or block read. In this case, the command
byte is the high byte of the EEPROM address from 80h to 9Fh.
The (only) data byte is the low byte of the EEPROM address.
This is illustrated in Figure 21.
S
ASLAVE
EEPROM
ADDRESS
HIGH BYTE
(80h TO 9Fh)
1
3
4
5
6
A
A
7
A
2
P
8
EEPROM
ADDRESS
LOW BYTE
(00h TO FFh)
0
Figure 21. Setting an EEPROM Address
If it is required to read data from the EEPROM immediately
after setting up the address, the master can assert a repeat start
condition immediately after the final ACK and carry out a
single-byte read or block read operation without asserting an
intermediate stop condition. In this case, Bit 0 of EEPROM
Register 3 should be set.
The third use is to erase a page of EEPROM memory. EEPROM
memory can be written to only if it is previously erased. Before
writing to one or more EEPROM memory locations that are
already programmed, the page or pages containing those
locations must first be erased. EEPROM memory is erased by
writing an EEPROM page address plus an arbitrary byte of data
with Bit 2 of EEPROM Register 3 set to 1.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1030ARQ | Intelligent Temperature Monitor and PWM Fan Controller |
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
| ADM1033 | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ-REEL | Thermal Monitor and Fan Speed (RPM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1026JST-REEL | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-R7 | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-REEL | 功能描述:板上安裝溫度傳感器 HI INT SYS MONITR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。