- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1026JST (ANALOG DEVICES INC) Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 PDF資料下載
參數資料
| 型號： | ADM1026JST |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026BBC, LQFP-48 |
| 文件頁數： | 16/56頁 |
| 文件大小： | 634K |
| 代理商： | ADM1026JST |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
ADM1026
Block Read
In this operation, the master device reads a block of data from a
slave device. The start address for a block read must have been
set previously. In the case of the ADM1026 this is done by a
send byte operation to set a RAM address, or by a write
byte/word operation to set an EEPROM address. The block read
operation consists of a send byte operation that sends a block
read command to the slave, immediately followed by a repeated
start and a read operation that reads out multiple data bytes as
follows:
1.
The master device asserts a start condition on the SDA.
2.
The master sends the 7-bit slave address followed by the
write bit (low).
3.
The addressed slave device asserts an ACK on the SDA.
4.
The master sends a command code that tells the slave
device to expect a block read. The ADM1026 command
code for a block read is A1h (10100001).
5.
The slave asserts an ACK on the SDA.
6.
The master asserts a repeat start condition on the SDA.
7.
The master sends the 7-bit slave address followed by the
read bit (high).
8.
The slave asserts an ACK on the SDA.
9.
The ADM1026 sends a byte count data byte that tells the
master how many data bytes to expect. The ADM1026
always returns 32 data bytes (20h), the maximum allowed
by the SMBus 1.1 specification.
10.
The master asserts an ACK on the SDA.
11.
The master receives 32 data bytes.
12.
The master asserts an ACK on the SDA after each data byte.
13.
The ADM1026 issues a PEC byte to the master. The master
should check the PEC byte and issue another block read if
the PEC byte is incorrect.
14.
A NACK is generated after the PEC byte to signal the end
of the read.
15.
The master asserts a stop condition on the SDA to end the
transaction.
Rev. A | Page 16 of 56
S
SLAVE
ADDRESS
W
A
COMMAND
A1h BLOCK
READ
A
S
R
A
P
DATA
32
PEC
A
A
BYTE
COUNT
A DATA 1
A
SLAVE
ADDRESS
0
Figure 26. Block Read from EEPROM or RAM
When block reading from EEPROM, Bit 0 of EEPROM
Register 3 must be set.
Note that although the ADM1026 supports packet error
checking (PEC), its use is optional. The PEC byte is calculated
using CRC-8. The frame check sequence (FCS) conforms to
CRC-8 by the polynomial:
C(x) = x
8
+ x
2
+ x
1
+ 1
Consult the SMBus 1.1 Specification for more information.
MEASUREMENT INPUTS
The ADM1026 has 17 external analog measurement pins that
can be configured to perform various functions. It also meas-
ures two supply voltages, 3.3 V MAIN and 3.3 V STBY, and the
internal chip temperature.
Pins 25 and 26 are dedicated to remote temperature measure-
ment, while Pins 27 and 28 can be configured as analog inputs
with a range of 0 V to 2.5 V, or as inputs for a second remote
temperature sensor.
Pins 29 to 33 are dedicated to measuring V
BAT
, +5 V, 12 V,
+12 V supplies, and the processor core voltage V
CCP.
The
remaining analog inputs, Pins 34 to 41, are general-purpose
analog inputs with a range of 0 V to 2.5 V (Pins 34 and 35) or
0 V to 3 V (Pins 36 to 41).
A-to-D Converter (ADC)
These inputs are multiplexed into the on-chip, successive
approximation, analog-to-digital converter. The ADC has a
resolution of 8 bits. The basic input range is 0 V to 2.5 V, which
is the input range of A
IN6
to A
IN9
, but five of the inputs have
built-in attenuators to allow measurement of V
BAT
, +5 V,
12 V,
+12 V, and the processor core voltage V
CCP
, without any external
components. To allow the tolerance of these supply voltages, the
ADC produces an output of 3/4 full scale (decimal 192) for the
nominal input voltage, and so has adequate headroom to cope
with over voltages. Table 6 shows the input ranges of the analog
inputs and output codes of the ADC.
When the ADC is running, it samples and converts an analog
or local temperature input every 711 μs (typical value). Each
input is measured 16 times and the measurements are averaged
to reduce noise, so the total conversion time for each input is
11.38 ms.
Measurements on the remote temperature (D1 and D2) inputs
take 2.13 ms. These are also measured 16 times and are
averaged, so the total conversion time for a remote temperature
input is 34.13 ms.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1030ARQ | Intelligent Temperature Monitor and PWM Fan Controller |
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
| ADM1033 | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ-REEL | Thermal Monitor and Fan Speed (RPM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1026JST-REEL | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-R7 | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-REEL | 功能描述:板上安裝溫度傳感器 HI INT SYS MONITR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。