- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1026JST (ANALOG DEVICES INC) Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 PDF資料下載
參數資料
| 型號： | ADM1026JST |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026BBC, LQFP-48 |
| 文件頁數： | 20/56頁 |
| 文件大小： | 634K |
| 代理商： | ADM1026JST |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
ADM1026
If the V
REF
output is not being used, it should be left uncon-
nected. Do not connect V
REF
to GND using a capacitor. The
internal output buffer on the voltage reference is capacitively
loaded, which can cause the voltage reference to oscillate. This
affects temperature readings reported back by the ADM1026.
The recommended interface circuit for the V
REF
output is shown
in Figure 33.
Rev. A | Page 20 of 56
10k
0.1
μ
F
ADM1026
24
+12V
0.1
μ
F
10
μ
F
50
V
REF
NDT3055
V
REF
0
Figure 33. V
REF
Interface Circuit for V
REF
Loads > 2 mA
TEMPERATURE MEASUREMENT SYSTEM
Local Temperature Measurement
The ADM1026 contains an on-chip band gap temperature
sensor whose output is digitized by the on-chip ADC. The
temperature data is stored in the local temperature value
register (Address 1Fh). As both positive and negative temper-
atures can be measured, the temperature data is stored in twos
complement format, as shown in Table 7. Theoretically, the
temperature sensor and ADC can measure temperatures from
128°C to +127°C with a resolution of 1°C. Temperatures below
T
MIN
and above T
MAX
are outside the operating temperature
range of the device, however, so local temperature measure-
ments outside this range are not possible. Temperature
measurement from 128°C to +127°C is possible using a
remote sensor.
Remote Temperature Measurement
The ADM1026 can measure the temperature of two remote
diode sensors, or diode-connected transistors, connected to
Pins 25 and 26, or 27 and 28.
Pins 25 and 26 are a dedicated temperature input channel.
Pins 27 and 28 can be configured to measure a diode sensor by
clearing Bit 3 of Configuration Register 1 (Address 00h) to 0.
If this bit is 1, then Pins 27 and 28 are A
IN8
and A
IN9
.
The forward voltage of a diode or diode-connected transistor,
operated at a constant current, exhibits a negative temperature
coefficient of about 2 mV/°C. Unfortunately, the absolute
value of V
be
varies from device to device, and individual
calibration is required to null this out, so the technique is
unsuitable for mass production.
The technique used in the ADM1026 is to measure the change
in V
be
when the device is operated at two different currents,
given by
( )
n
q
T
K
V
be
log
Δ
×
×
=
where
K
is Boltzmann’s constant,
q
is the charge on the carrier,
T
is the absolute temperature in Kelvins, and
N
is the ratio of
the two currents.
Figure 34 shows the input signal conditioning used to measure
the output of a remote temperature sensor. This figure shows
the external sensor as a substrate transistor provided for
temperature monitoring on some microprocessors, but it could
equally well be a discrete transistor such as a 2N3904.
If a discrete transistor is used, the collector is not grounded
and should be linked to the base. If a PNP transistor is used,
the base is connected to the D input and the emitter to the
D+ input. If an NPN transistor is used, the emitter is connected
to the D input and the base to the D+ input.
To prevent ground noise from interfering with the measure-
ment, the more negative terminal of the sensor is not referenced
to ground but is biased above ground by an internal diode at the
D input.
To measure ΔV
be
, the sensor is switched between operating
currents of I and N × I. The resulting waveform is passed
through a 65 kHz low-pass filter to remove noise, and to a
chopper-stabilized amplifier that performs the functions of
amplification and rectification of the waveform to produce a
DC voltage proportional to ΔV
be
. This voltage is measured
by the ADC to give a temperature output in 8-bit, twos
complement format. To further reduce the effects of noise,
digital filtering is performed by averaging the results of 16
measurement cycles. A remote temperature measurement
takes nominally 2.14 ms.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1030ARQ | Intelligent Temperature Monitor and PWM Fan Controller |
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
| ADM1033 | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ-REEL | Thermal Monitor and Fan Speed (RPM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1026JST-REEL | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-R7 | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-REEL | 功能描述:板上安裝溫度傳感器 HI INT SYS MONITR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。