- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1041A (Analog Devices, Inc.) Secondary-Side Controller with Current Share and Housekeeping PDF資料下載
參數資料
| 型號： | ADM1041A |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Secondary-Side Controller with Current Share and Housekeeping |
| 中文描述： | 二次側電流控制器共享和管家 |
| 文件頁數： | 14/56頁 |
| 文件大小： | 991K |
| 代理商： | ADM1041A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
ADM1041A
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Rev. 0 | Page 14 of 56
ADM1041A
TOP VIEW
(Not to Scale)
V
DD
1
V
LS
/C
S
–/FS
2
C
S
+
C
CMP
V
CMP
3
4
5
SHRO
SHRS+
SCMP
V
S
+
V
S
–/SHRS–
F
G
AC_OK/OTP/MON5
24
23
22
21
20
F
D
6
GND
7
ICT
8
PULSE/AC
SENSE
1/MON1
AC
SENSE
2/MON2
10
CBD/ALERT
11
9
DC_OK/MON4
PSON/MON3
19
18
17
16
PEN
12
ADD0
SDA/PS
ON
LINK
SCL/AC_OKLink
15
14
13
0
Figure 7. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
Mnemonic
1
V
DD
2
V
LS
/C
S
–/FS
Description
Positive Supply for the ADM1041A. Normal range is 4.5 V to 5.5 V. Absolute maximum rating is 6.5 V.
Inverting Differential Current Sense Input, Local Voltage Sense Pin, and OrFET Source. These three functions
are served by a common divider. The local voltage sense input is used for local overvoltage and undervoltage
sensing. This pin also provides an input to the false UV clamp that prevents shutdown during an external load
overvoltage condition. When supporting an OrFET circuit, this pin represents the FET source and is the
inverting input of a differential amplifier looking for the presence of a reverse voltage across the FET, which
might indicate a failure mode.
Noninverting Differential Current Sense Input. The differential sensitivity of C
S
+ and C
S
– is normally around 10
mV to 40 mV at the input to the ADM1041A. Nulling any external divider offset is achieved by injecting a
trimmable amount of current into either the inverting or noninverting input of the second stage of the
current sense amplifier. A compensation circuit is used to ensure the amount of current for zero-offset tracks
the common-mode voltage. Nulling of any amplifier offset is done in a similar manner except that it does not
track the common-mode voltage.
Current Error Amplifier Compensation. This pin is the output of the current limit transconductance error
amplifier. A series resistor and a capacitor to ground are required for loop compensation.
Voltage Error Amplifier Compensation. This is the output of a voltage error transconductance amplifier.
Compensate with a series capacitor and resistor to ground. An external emitter-follower or buffer is typically
used to drive an optocoupler. Output voltage positioning may be obtained by placing a second resistor
directly to ground. Refer to Analog Devices applications notes on voltage positioning.
A divider from the OrFET drain is connected here. A differential amplifier is then used to detect the presence
of a reverse voltage across the FET, which indicates a fault condition and causes the OrFET gate to be pulled
low.
Ground. This pin is double bonded for extra reliability. If the ground pin goes positive with respect to the
remote sense return (V
S
–) for a sustained period indicating that the negative remote sense line is
disconnected, PEN is disabled.
Input for Current Transformer. The sensitivity of this pin is suitable for the typical 0.5 V to 1 V signal that is
normally available. If this function is enabled, the C
S
+ amplifier is disabled. This pin is also used for extended
SMBus addressing, that is, pulled below ground to allow additional SMBus addresses.
Pulse Present, AC/Bulk Sense 1, or Monitor 1 Input.
PULSE: This tells the OrFET circuit that the voltage from the power transformer is normal. A peak hold allows
the OrFET circuit to pass through the pulse skipping that occurs with very light loads, but turns off the circuit
about one second after the last pulse is recognized.
AC
SENSE
1: This sense function also uses the peak voltage on this pin to measure the bulk capacitor voltage. If
too low, AC_OK and DC_OK can warn of an imminent loss of power. Threshold level and hysteresis can be
trimmed. When not selected, AC
SENSE
1 defaults to true.
MON1: When MON1 is selected for this pin, its input is compared against a 1.25 V comparator that could be
used for monitoring a postregulated output; includes overvoltage, undervoltage, and overtemperature
conditions.
3
C
S
+
4
C
CMP
5
V
CMP
6
F
D
7
GND
8
ICT
9
PULSE/AC
SENSE
1/
MON1
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1041AARQZ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1052 | Precision Dual Voltage Regulator Controller |
| ADM1052JR | Precision Dual Voltage Regulator Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1041AARQZ | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ADM1041AARQZ-REEL | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ADM1041AARQZ-REEL7 | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 標準包裝:1 系列:- 主要目的:DC/DC，步降 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓?fù)浣Y(jié)構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND |
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。