欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADM1041AARQZ-REEL7
廠商: ANALOG DEVICES INC
元件分類: 通信及網絡
英文描述: Secondary-Side Controller with Current Share and Housekeeping
中文描述: SPECIALTY TELECOM CIRCUIT, PDSO24
封裝: LEAD FREE, MO-137AE, QSOP-24
文件頁數: 20/56頁
文件大小: 991K
代理商: ADM1041AARQZ-REEL7
ADM1041A
Rev. 0 | Page 20 of 56
0
20
60
50
30
10
40
70
0
1
2
3
4
VOLTAGE (V)
C
μ
A
0
Figure 10. Current Limit
0
0.75
1.00
2.25
2.00
1.25
0.50
0.25
1.50
1.75
2.75
2.50
1
10
100
1k
10k
100k
1M
10M
100M
BANDWIDTH
G
0
Figure 11. V
CMP
Transconductance
0
60
80
180
160
100
40
20
120
140
220
200
1
10
100
1k
10k
100k
1M
10M
100M
BANDWIDTH
G
μ
A
0
Figure 12. C
CMP
and S
CMP
Transconductance
VOLTAGE ERROR AMPLIFIER
This is a high gain transconductance amplifier that takes its
input from the load voltage trim stage described previously. The
amplifier requires only the output pin for loop compensation,
which typically consists of a series RC network-to-common. A
parallel resistor may be added to common to reduce the open-
loop gain and thereby provide some output voltage droop as
output current increases. The output of the amplifier is typically
connected to an emitter follower that drives an optocoupler,
which in turn controls the duty of the primary side PWM. The
emitter follower should have a high gain to minimize loading
effects on the amplifier. Alternatively, an op amp voltage
follower may be used. See Figure 11.
MAIN VOLTAGE REFERENCE
A 1.5 V reference is connected to the inverting input of the
voltage error amplifier. This 1.5 V reference is the output
voltage of the soft-start circuit. Under closed-loop conditions,
the voltage at the noninverting input is also controlled to 1.5 V.
During start-up, the output voltage should be ramped up in a
linear fashion at a rate that is independent of the load current.
This is achieved by digitally ramping up the reference voltage by
using a counter and a DAC. The ramp rate is configurable via
the SMBus. See Figure 13.
CURRENT-SENSE AMPLIFIER
This is a two-stage differential amplifier that achieves low offset
and accuracy. The amplifier has the option to be chopped to
reduce offset or left as a linear amplifier without chopping.
Refer to the Register Listing for more details. The amplifier’s
gain can be selected from three ranges. It is followed by a trim
stage and then by a low gain buffer stage that can be configured
with a gain of 1.0 or 2.1. The result is a total of six overlapping
gain ranges (65 to 230), one of which must be selected via the
SMBus. This gives ample adjustment to compensate for the
poor initial tolerance of the resistance wires typically used for
current sensing. It also allows selecting a higher sensitivity for
better efficiency or a lower sensitivity for better accuracy (lower
offset). The amplifier offset voltage is trimmed to zero in a
once-off operation via the SMBus and uses a voltage-controlled
current source at the output of the first gain stage. A second
controlled current source is used to trim out the additional
offset due to the mismatch of the external divider resistors. This
offset trim is dynamically adjusted according to the common-
mode voltage present at the top of the voltage dividers. Six
ranges are selectable according to the magnitude and polarity of
this offset component. Because the offset compensation circuit
itself has some inaccuracies, the best overall current-sense
accuracy is obtained by using more closely matched external
dividers and then selecting a low compensation range. See
Figure 13.
相關PDF資料
PDF描述
ADM1052 Precision Dual Voltage Regulator Controller
ADM1052JR Precision Dual Voltage Regulator Controller
ADM1060 DIP Socket; No. of Contacts:56; Pitch Spacing:0.07"; Row Spacing:0.6"; Terminal Type:PC Board; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):No RoHS Compliant: Yes
ADM1060ARU CON-HDR64POS2ROW 4WALL.1X.1SP,RTANG,LOPF
ADM1064 Super Sequencer with Voltage Readback ADC
相關代理商/技術參數
參數描述
ADM1041A-EVALZ 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 類別:編程器,開發系統 >> 評估板 - DC/DC 與 AC/DC(離線)SMPS 系列:- 標準包裝:1 系列:- 主要目的:DC/DC,步降 輸出及類型:1,非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓?fù)浣Y(jié)構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND
ADM1041ARQ 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器,監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(5x5) 包裝:帶卷 (TR)
ADM1041ARQ-2 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADM1041ARQ-REEL 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping
ADM1041ARQ-REEL7 功能描述:IC PWR SUP MON/LOAD SHARE 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器,監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(5x5) 包裝:帶卷 (TR)
主站蜘蛛池模板: 新郑市| 宿迁市| 泾阳县| 扶风县| 南岸区| 宜君县| 集贤县| 孟村| 卢氏县| 南江县| 修水县| 元氏县| 古交市| 安徽省| 左权县| 错那县| 新郑市| 隆德县| 竹溪县| 兰西县| 宜春市| 呼玛县| 岳阳县| 县级市| 文成县| 东山县| 夹江县| 淮阳县| 丹凤县| 祁连县| 泉州市| 葵青区| 赤水市| 丰顺县| 长宁县| 区。| 竹溪县| 特克斯县| 莒南县| 广德县| 北安市|