- 您現在的位置：買賣IC網 > PDF目錄374032 > ADSP-21061KS-133 (ANALOG DEVICES INC) ADSP-2106x SHARC DSP Microcomputer Family PDF資料下載
參數資料
| 型號： | ADSP-21061KS-133 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | ADSP-2106x SHARC DSP Microcomputer Family |
| 中文描述： | 48-BIT, 33 MHz, OTHER DSP, PQFP240 |
| 封裝： | MQFP-240 |
| 文件頁數： | 12/47頁 |
| 文件大小： | 367K |
| 代理商： | ADSP-21061KS-133 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
–12–
ADSP-21061/ADSP-21061L
REV. B
The 14-pin, 2-row pin strip header is keyed at the Pin 3 location —
Pin 3 must be removed from the header. The pins must be
0.025 inch square and at least 0.20 inch in length. Pin spacing
should be 0.1
×
0.1 inches. Pin strip headers are available from
vendors such as 3M, McKenzie and Samtec.
The BTMS, BTCK,
BTRST
and BTDI signals are provided so
the test access port can also be used for board-level testing.
When the connector is not being used for emulation, place
jumpers between the Bxxx pins and the xxx pins. If the test
access port will not be used for board testing, tie
BTRST
to GND
and tie or pull BTCK up to VDD. The
TRST
pin must be
asserted after power-up (through
BTRST
on the connector) or
held low for proper operation of the ADSP-2106x. None of the
Bxxx pins (Pins 5, 7, 9, 11) are connected on the EZ-ICE
probe.
The JTAG signals are terminated on the EZ-ICE probe as
follows:
Signal
Termination
Driven through 22
Resistor (16 mA Driver)
Driven at 10 MHz through 22
Resistor (16 mA
Driver)
TRST
* Active Low Driven through 22
Resistor (16 mA
Driver) (Pulled Up by On-Chip 20 k
Resistor)
TDI
Driven by 22
Resistor (16 mA Driver)
TDO
One TTL Load, Split Termination (160/220)
CLKIN One TTL Load, Split Termination (160/220)
EMU
Active Low 4.7 k
Pull-Up Resistor, One TTL Load
(Open-Drain Output from the DSP)
TMS
TCK
*
TRST
is driven low until the EZ-ICE
probe is turned on by the emulator at
software start-up. After software start-up,
TRST
is driven high.
Figure 6 shows JTAG scan path connections for systems that
contain multiple ADSP-2106x processors.
TARGET BOARD CONNECTOR FOR EZ-ICE
PROBE
The ADSP-2106x EZ-ICE Emulator uses the IEEE 1149.1
JTAG test access port of the ADSP-2106x to monitor and control
the target board processor during emulation. The EZ-ICE
probe requires the ADSP-2106x’s CLKIN, TMS, TCK,
TRST
, TDI, TDO,
EMU
, and GND signals be made acces-
sible on the target system via a 14-pin connector (a 2 row
×
7
pin strip header) such as that shown in Figure 5. The EZ-ICE
probe plugs directly onto this connector for chip-on-board
emulation. You must add this connector to your target board
design if you intend to use the ADSP-2106x EZ-ICE. The total
trace length between the EZ-ICE connector and the furthest
device sharing the EZ-ICE JTAG pins should be limited to 15
inches maximum for guaranteed operation. This length restric-
tion must include EZ-ICE JTAG signals that are routed to one
or more ADSP-2106x devices, or a combination of ADSP-
2106x devices and other JTAG devices on the chain.
TOP VIEW
13
14
11
12
9
10
9
7
8
5
6
3
4
1
2
EMU
CLKIN (OPTIONAL)
TMS
TCK
TRST
TDI
TDO
GND
KEY (NO PIN)
BTMS
BTCK
BTRST
BTDI
GND
Figure 5. Target Board Connector For ADSP-21061/ADSP-
21061L EZ-ICE
Emulator (Jumpers in Place)
ADSP-2106x
#1
JTAG
DEVICE
(OPTIONAL)
ADSP-2106x
#n
TDI
EZ-ICE
JTAG
CONNECTOR
OTHER
JTAG
CONTROLLER
OPTIONAL
T
T
EMU
TRST
TMS
TCK
TDO
CLKIN
T
T
T
T
TDI
TDO
TDI
TDO
TDO
TDI
E
T
E
T
T
Figure 6. JTAG Scan Path Connections for Multiple ADSP-21061/ADSP-21061L Systems
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21061 | ADSP-2106x SHARC DSP Microcomputer Family |
| ADSP-21061L | ADSP-2106x SHARC DSP Microcomputer Family |
| ADSP-21061LAS-160 | ADSP-2106x SHARC DSP Microcomputer Family |
| ADSP-21061LAS-176 | ADSP-2106x SHARC DSP Microcomputer Family |
| ADSP-21061KS-160 | ADSP-2106x SHARC DSP Microcomputer Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21061KS-160 | 功能描述:IC DSP CONTROLLER 1MBIT 240MQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，FCBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21061KS-200 | 功能描述:IC DSP CONTROLLER 32BIT 240MQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，FCBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21061KS-200X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:32-Bit Digital Signal Processor |
| ADSP-21061KSZ-133 | 功能描述:IC DSP CONTROLLER 32BIT 240MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，FCBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21061KSZ-160 | 功能描述:IC DSP CONTROLLER 1MBIT 240MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，FCBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
發布緊急采購，3分鐘左右您將得到回復。