- 您現在的位置：買賣IC網 > PDF目錄374037 > ADSP-21990 (Analog Devices, Inc.) 16-bit fixed point DSP with Flash PDF資料下載
參數資料
| 型號： | ADSP-21990 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 數字信號處理 |
| 英文描述： | 16-bit fixed point DSP with Flash |
| 中文描述： | 具有閃存的 16 位定點 DSP |
| 文件頁數： | 9/44頁 |
| 文件大小： | 574K |
| 代理商： | ADSP-21990 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
–9–
REV. 0
ADSP-21990
The ADSP-21990 integrates a flexible and programmable,
3-phase PWM waveform generator that can be programmed to
generate the required switching patterns to drive a 3-phase
voltage source inverter for ac induction (ACIM) or permanent
magnet synchronous (PMSM) motor control. In addition, the
PWM block contains special functions that considerably simplify
the generation of the required PWM switching patterns for
control of the electronically commutated motor (ECM) or
brushless dc motor (BDCM). Tying a dedicated pin,
PWMSR
,
to GND, enables a special mode, for switched reluctance motors
(SRM).
The six PWM output signals consist of three high side drive pins
(AH, BH, and CH) and three low side drive signals pins (AL,
BL, and CL). The polarity of the generated PWM signals may
be set via hardware by the PWMPOL input pin, so that either
active HI or active LO PWM patterns can be produced.
The switching frequency of the generated PWM patterns is pro-
grammable using the 16-bit PWMTM register. The PWM
generator is capable of operating in two distinct modes, single
update mode or double update mode. In single update mode the
duty cycle values are programmable only once per PWM period,
so that the resultant PWM patterns are symmetrical about the
midpoint of the PWM period. In the double update mode, a
second updating of the PWM registers is implemented at the
midpoint of the PWM period. In this mode, it is possible to
produce asymmetrical PWM patterns. that produce lower
harmonic distortion in 3-phase PWM inverters.
Auxiliary PWM Generation Unit
Key features of the auxiliary PWM generation unit are:
16-bit, programmable frequency, programmable duty
cycle PWM outputs
Independent or offset operating modes
Double buffered control of duty cycle and period registers
Separate auxiliary PWM synchronization signal and asso-
ciated interrupt (can be used to trigger ADC Convert
Start)
Separate auxiliary PWM shutdown signal (
AUXTRIP
)
The ADSP-21990 integrates a 2-channel, 16-bit, auxiliary PWM
output unit that can be programmed with variable frequency,
variable duty cycle values and may operate in two different
modes, independent mode or offset mode. In independent mode,
the two auxiliary PWM generators are completely independent
and separate switching frequencies and duty cycles may be pro-
grammed for each auxiliary PWM output. In offset mode the
switching frequency of the two signals on the AUX0 and AUX1
pins is identical. Bit 4 of the AUXCTRL register places the
auxiliary PWM channel pair in independent or offset mode.
The auxiliary PWM generation unit provides two chip output
pins, AUX0 and AUX1 (on which the switching signals appear)
and one chip input pin,
AUXTRIP
, which can be used to shut
down the switching signals—for example, in a fault condition.
Encoder Interface Unit
The ADSP-21990 incorporates a powerful encoder interface
block to incremental shaft encoders that are often used for
position feedback in high performance motion control systems.
Quadrature rates to 53 MHz (at 80 MHz HCLK rate)
Programmable filtering of all encoder input signals
32-bit encoder counter
Variety of hardware and software reset modes
Two registration inputs to latch EIU count value with
corresponding registration interrupt
Status of A/B signals latched with reading of EIU count
value
Alternative frequency and direction mode
Single north marker mode
Count error monitor function with dedicated error
interrupt
Dedicated 16-bit loop timer with dedicated interrupt
Companion encoder event (1
T) timer unit
The encoder interface unit (EIU) includes a 32-bit quadrature
up/down counter, programmable input noise filtering of the
encoder input signals and the zero markers, and has four
dedicated chip pins. The quadrature encoder signals are applied
at the EIA and EIB pins. Alternatively, a frequency and direction
set of inputs may be applied to the EIA and EIB pins. In addition,
two north marker/strobe inputs are provided on pins EIZ and
EIS. These inputs may be used to latch the contents of the
encoder quadrature counter into dedicated registers,
EIZLATCH and EISLATCH, on the occurrence of external
events at the EIZ and EIS pins. These events may be programmed
to be either rising edge only (latch event) or rising edge if the
encoder is moving in the forward direction and falling edge if the
encoder is moving in the reverse direction (software latched north
marker functionality).
The encoder interface unit incorporates programmable noise
filtering on the four encoder inputs to prevent spurious noise
pulses from adversely affecting the operation of the quadrature
counter. The encoder interface unit operates at a clock frequency
equal to the HCLK rate. The encoder interface unit operates
correctly with encoder signals at frequencies of up to 13.25 MHz
at the 80 MHz HCLK rate, corresponding to a maximum
quadrature frequency of 53 MHz (assuming an ideal quadrature
relationship between the input EIA and EIB signals).
The EIU may be programmed to use the north marker on EIZ
to reset the quadrature encoder in hardware, if required.
Alternatively, the north marker can be ignored, and the encoder
quadrature counter is reset according to the contents of a
maximum count register, EIUMAXCNT. There is also a “single
north marker” mode available in which the encoder quadrature
counter is reset only on the first north marker pulse.
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21990BBC | 16-bit fixed point DSP with Flash |
| ADSP-21990BST | 16-bit fixed point DSP with Flash |
| ADSP-21MOD870-100 | Single Chip Digital Modem(單片數字調制解調器) |
| ADSP-21MOD870-110 | Internet Gateway Processor Software |
| ADSP-21MOD870 | Internet Gateway Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21990BBC | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin Mini-BGA 制造商:Rochester Electronics LLC 功能描述:160 MIPS, MIXED SIGNAL DSPWITH 14-BIT - Bulk |
| ADSP-21990BST | 制造商:Rochester Electronics LLC 功能描述:160 MIPS,MIXED SIGNAL DSP WITH 14BIT - Tape and Reel |
| ADSP-21990BSTZ | 功能描述:IC DSP CONTROLLER 16BIT 176-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，FCBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21991BBC | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin Mini-BGA |
| ADSP-21991BBCZ | 功能描述:IC DSP CTLR 16BIT 196CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，FCBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。