- 您現在的位置：買賣IC網 > PDF目錄374038 > ADT7460ARQ (ANALOG DEVICES INC) dB COOL?? Remote Thermal Controller and Fan Controller PDF資料下載
參數資料
| 型號： | ADT7460ARQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | dB COOL?? Remote Thermal Controller and Fan Controller |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | 0.025 INCH PITCH, MO-137AB, QSOP-16 |
| 文件頁數： | 35/48頁 |
| 文件大小： | 695K |
| 代理商： | ADT7460ARQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
REV. 0
ADT7460
–35–
Table XII. Register 0x40 – Configuration Register 1 (Power-On Default = 0x00)
Bit
<0>
Name
STRT
R/W
Read/Write
Description
Logic 1 enables monitoring and PWM control outputs based on the limit settings pro-
grammed. Logic 0 disables monitoring and PWM control based on the default power-up
limit settings. Note that the limit values programmed are preserved even if a logic 0 is
written to this bit and the default settings are enabled. This bit becomes read-only and
cannot be changed once Bit 1 (LOCK bit) has been written. All limit registers should be
programmed by BIOS before setting this bit to 1. (Lockable.)
Logic 1 locks all limit values to their current settings. Once this bit is set, all lockable
registers become read-only and cannot be modified until the ADT7460 is powered down
and powered up again. This prevents rogue programs such as viruses from modifying
critical system limit settings. (Lockable.)
This bit gets set to 1 by the ADT7460 to indicate that the device is fully powered-up
and ready to begin systems monitoring.
When set to 1, this runs all fans at full speed. Power-on default = 0. This bit does not
get locked at any time.
Read Only and Reserved for Future Use
Logic 1 disables fan spin-up for two TACH pulses. Instead, the PWM outputs will go
high for the entire fan spin-up timeout selected.
When this bit is set to 1, the SMBus timeout feature is disabled. This allows the
ADT7460 to be used with SMBus controllers that cannot handle SMBus
timeouts. (Lockable.)
When this bit is set to 1, the ADT7460 rescales its V
CC
pin to measure a 5 V supply. If
this bit is 0, the ADT7460 measures V
CC
as a 3.3 V supply. (Lockable.)
<1>
LOCK
Write Once
<2>
RDY
Read Only
<3>
FSPD
Read/Write
<4>
<5>
Reserved
FSPDIS
Read/Write
<6>
TODIS
Read/Write
<7>
VCC
Read/Write
Table XIII. Register 0x41 – Interrupt Status Register 1 (Power-On Default = 0x00)
Bit
<0>
Name
2.5V
R/W
Read Only
Description
A one indicates the 2.5 V
High or Low limit has been exceeded. This bit gets cleared on
a read of the Status Register only if the error condition has subsided.
Reserved for future use
A one indicates the V
CC
High or Low limit has been exceeded. This bit gets cleared on a
read of the Status Register only if the error condition has subsided.
Reserved for future use
A one indicates the Remote 1 Low or High Temp limit has been exceeded. This bit gets
cleared on a read of the Status Register only if the error condition has subsided.
A one indicates the Local Low or High Temp limit has been exceeded. This bit gets
cleared on a read of the Status Register only if the error condition has subsided.
A one indicates the Remote 2 Low or High Temp limit has been exceeded. This bit gets
cleared on a read of the Status Register only if the error condition has subsided.
A one indicates that an Out-of-Limit event has been latched in Status Register 2. This
bit is a logical OR of all status bits in Status Register 2. Software can test this bit in
isolation to determine whether any of the voltage, temperature, or fan speed readings
represented by Status Register 2 are out-of-limit. This saves the need to read Status
Register 2 every interrupt or polling cycle.
<1>
<2>
Unused
V
CC
Read Only
Read Only
<3>
<4>
Unused
R1T
Read Only
Read Only
<5>
LT
Read Only
<6>
R2T
Read Only
<7>
OOL
Read Only
ADOPT is a trademark of Analog Devices, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7461 | 【1∑C Temperature Monitor with Series Resistance Cancellation |
| ADT7461AR | 【1∑C Temperature Monitor with Series Resistance Cancellation |
| ADT7461AR-REEL | 【1∑C Temperature Monitor with Series Resistance Cancellation |
| ADT7461AR-REEL7 | 【1∑C Temperature Monitor with Series Resistance Cancellation |
| ADT7461ARM | 【1∑C Temperature Monitor with Series Resistance Cancellation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7460ARQ-REEL | 功能描述:IC SENSOR TEMP FAN-CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7460ARQ-REEL7 | 功能描述:IC SENSOR TEMP FAN-CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7460ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 THERMAL MGMT CNTRLR IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADT7460ARQZ-R7 | 制造商:ON Semiconductor 功能描述:Temp Sensor Digital Serial (3-Wire) 16-Pin QSOP T/R |
| ADT7460ARQZ-REEL | 功能描述:板上安裝溫度傳感器 THERMAL MGMT CNTRLR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。