- 您現在的位置：買賣IC網 > PDF目錄374038 > ADT7460ARQ (ANALOG DEVICES INC) dB COOL?? Remote Thermal Controller and Fan Controller PDF資料下載
參數資料
| 型號： | ADT7460ARQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | dB COOL?? Remote Thermal Controller and Fan Controller |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | 0.025 INCH PITCH, MO-137AB, QSOP-16 |
| 文件頁數： | 41/48頁 |
| 文件大小： | 695K |
| 代理商： | ADT7460ARQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
REV. 0
ADT7460
–41–
Table XXII. PWM Min Duty Cycle Registers
Register Address
0x64
0x65
0x66
Bit
<7:0>
R/W
*
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Description
PWM1 Min Duty Cycle
PWM2 Min Duty Cycle
PWM3 Min Duty Cycle
Description
These bits define the PWM
MIN
duty cycle for PWMx.
0x00 = 0% duty cycle (Fan off)
0x40 = 25% duty cycle
0x80 = 50% duty cycle
0xFF = 100% duty cycle (Fan full speed)
Power-On Default
0x80 (50% duty cycle)
0x80 (50% duty cycle)
0x80 (50% duty cycle)
Name
PWM Duty
Cycle
*
These registers become read-only when the ADT7460 is in Automatic Fan Control Mode.
Table XXIII. T
MIN
Registers
Register Address
0x67
0x68
0x69
R/W
*
Read/Write
Read/Write
Read/Write
Description
Remote 1 Temp T
MIN
Local Temp T
MIN
Remote 2 Temp T
MIN
Power-On Default
0x5A (90 C)
0x5A (90 C)
0x5A (90 C)
These are the T
MIN
registers for each temperature channel. When the temperature measured exceeds T
MIN
, the appropriate fan will run at minimum speed and
increase with temperature according to T
RANGE
.
*
These registers become read-only when the Configuration Register 1 Lock bit is set. Any further attempts to write to these registers shall have no effect.
Table XXIV.
THERM
Limit Registers
Register Address
0x6A
0x6B
0x6C
R/W
*
Read/Write
Read/Write
Read/Write
Description
Remote 1
THERM
Limit
Local
THERM
Limit
Remote 2
THERM
Limit
Power-On Default
0x64 (100 C)
0x64 (100 C)
0x64 (100 C)
If any temperature measured exceeds its
THERM
limit, all PWM outputs will drive their fans at 100% duty cycle. This is a fail-safe mechanism incorporated to cool
the system in the event of a critical overtemperature. It also ensures some level of cooling in the event that software or hardware locks up. If set to 0x80, this feature is
disabled. The PWM output will remain at 100% until the temperature drops below
THERM
limit – Hysteresis. If the
THERM
pin is programmed as an output, then
exceeding these limits by 0.25 C can cause the
THERM
pin to assert low as an output.
*
These registers become read-only when the Configuration Register 1 Lock bit is set to 1. Any further attempts to write to these registers will have no effect.
Table XXV. Temperature Hysteresis Registers
Register Address
0x6D
0x6E
R/W
*
Read/Write
Read/Write
Description
Remote 1, Local Temp Hysteresis
Remote 2 Temp Hysteresis
Power-On Default
0x44
0x40
Each 4-bit value controls the amount of temperature hysteresis applied to a particular temperature channel. Once the temperature for that channel falls below its T
value, the fan will remain running at PWM
duty cycle until the temperature = T
MIN
– Hysteresis. Up to 15 C of hysteresis may be assigned to any temperature
channel. The hysteresis value chosen will also apply to that temperature channel if its
limit is exceeded. The PWM output being controlled will go to 100% if
the
THERM
limit is exceeded and will remain at 100% until the temperature drops below
THERM
– Hysteresis. For acoustic reasons, it is recommended that the
hysteresis value not be programmed less than 4 C. Setting the hysteresis value lower than 4 C will cause the fan to switch on and off regularly when the temperature is
close to T
.
*
These registers become read-only when the Configuration Register 1 Lock bit is set to 1. Any further attempts to write to these registers will have no effect.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7461 | 【1∑C Temperature Monitor with Series Resistance Cancellation |
| ADT7461AR | 【1∑C Temperature Monitor with Series Resistance Cancellation |
| ADT7461AR-REEL | 【1∑C Temperature Monitor with Series Resistance Cancellation |
| ADT7461AR-REEL7 | 【1∑C Temperature Monitor with Series Resistance Cancellation |
| ADT7461ARM | 【1∑C Temperature Monitor with Series Resistance Cancellation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7460ARQ-REEL | 功能描述:IC SENSOR TEMP FAN-CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7460ARQ-REEL7 | 功能描述:IC SENSOR TEMP FAN-CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7460ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 THERMAL MGMT CNTRLR IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADT7460ARQZ-R7 | 制造商:ON Semiconductor 功能描述:Temp Sensor Digital Serial (3-Wire) 16-Pin QSOP T/R |
| ADT7460ARQZ-REEL | 功能描述:板上安裝溫度傳感器 THERMAL MGMT CNTRLR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。