欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： ADUC836
廠商： Analog Devices, Inc.
元件分類： 串行ADC
英文描述： MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
中文描述： MicroConverter的，雙16位ADC的與嵌入62 kB閃存微控制器
文件頁數： 31/80頁
文件大小： 5913K
代理商： ADUC836
ADuC836
–31–
User Download Mode (ULOAD)
In Figure 17 we can see that it was possible to use the 62 Kbytes
of Flash/EE program memory available to the user as one single
block of memory. In this mode, all of the Flash/EE memory is
read only to user code.
However, the Flash/EE program memory can also be written to
during runtime simply by entering ULOAD mode. In ULOAD
mode, the lower 56 Kbytes of program memory can be erased
and reprogrammed by user software, as shown in Figure 19.
ULOAD mode can be used to upgrade your code in the field via
any user defined download protocol. Configuring the SPI port on
the ADuC836 as a slave, it is possible to completely reprogram
the 56 Kbytes of Flash/EE program memory in only 5 seconds
(see Application Note uC007).
Alternatively, ULOAD mode can be used to save data to the
56 Kbytes of Flash/EE memory. This can be extremely useful in
data logging applications where the ADuC836 can provide up to
60 Kbytes of NV data memory on-chip (4 Kbytes of dedicated
Flash/EE data memory also exist).
The upper 6 Kbytes of the 62 Kbytes of Flash/EE program memory
are only programmable via serial download or parallel program-
ming. This means that this space appears as read-only to user
code. Therefore, it cannot be accidently erased or reprogrammed
by erroneous code execution. This makes it very suitable to use
the 6 Kbytes as a bootloader. A Bootload Enable option exists in
the serial downloader to “Always RUN from E000h after Reset.”
If using a bootloader, this option is recommended to ensure that
the bootloader always executes correct code after reset.
Programming the Flash/EE program memory via ULOAD mode
is described in more detail in the description of ECON and also
in Application Note uC007.
FFFFH
2 KBYTE
E000H
DFFFH
0000H
USER BOOTLOADER SPACE
THE USER BOOTLOADER SPACE
CAN BE PROGRAMMED IN
DOWNLOAD/DEBUG MODE VIA THE
KERNEL BUT IS READ ONLY WHEN
EXECUTING USER CODE
6 KBYTE
F800H
F7FFH
USER DOWNLOAD SPACE
EITHER THE DOWNLOAD/DEBUG KERNEL
OR USER CODE (IN ULOAD MODE) CAN
PROGRAM THIS SPACE.
EMBEDDED DOWNLOAD/DEBUG KERNEL
PERMANENTLY EMBEDDED FIRMWARE ALLOWS CODE
TO BE DOWNLOADED TO ANY OF THE 62 KBYTES OF
ON-CHIP PROGRAM MEMORY. THE KERNEL PROGRAM
APPEARS AS ‘NOP’ INSTRUCTIONS TO USER CODE.
56 KBYTE
62 KBYTES
OF USER
CODE
MEMORY
Figure 19. Flash/EE Program Memory Map in
ULOAD Mode
Flash/EE Program Memory Security
The ADuC836 facilitates three modes of Flash/EE program memory
security. These modes can be independently activated, restrict-
ing access to the internal code space. These security modes can
be enabled as part of serial download protocol, as described
in Application Note uC004, or via parallel programming. The
ADuC836 offers the following security modes:
Lock Mode
This mode locks the code memory, disabling parallel program-
ming of the program memory. However, reading the memory in
Parallel mode and reading the memory via a MOVC command
from external memory is still allowed. This mode is deactivated
by initiating an “erase code and data” command in Serial Down-
load or Parallel Programming modes.
Secure Mode
This mode locks the code memory, disabling parallel program-
ming of the program memory. Reading/verifying the memory
in Parallel mode and reading the internal memory via a MOVC
command from external memory is also disabled. This mode is
deactivated by initiating an “erase code and data” command in
Serial Download or Parallel Programming modes.
Serial Safe Mode
This mode disables serial download capability on the device.
If Serial Safe mode is activated and an attempt is made to reset
the part into Serial Download mode, i.e., RESET asserted and
deasserted with
PSEN
low, the part will interpret the serial
down-
load reset as a normal reset only. It will therefore not enter
Serial
Download mode, but only execute a normal reset
sequence.
Serial Safe mode can only be disabled by initiating an “erase code
and data” command in parallel programming mode.
REV. A
相關PDF資料
PDF描述
ADUC836BCP MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
ADUC836BS MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
ADUC842BCP62-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC843BCP62-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC842BCP62-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
相關代理商/技術參數
參數描述
ADUC836_02 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU
ADUC836BCP 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADUC836BCPZ 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC836BCPZ-REEL 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC836BS 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +16BIT DUAL ADC MQFP52
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 北宁市| 英吉沙县| 河北省| 宿州市| 万全县| 收藏| 八宿县| 绥德县| 阿鲁科尔沁旗| 周至县| 平原县| 安泽县| 西和县| 韶关市| 遵化市| 长治市| 东安县| 安陆市| 张掖市| 广平县| 灵山县| 易门县| 阳江市| 古交市| 娱乐| 当雄县| 怀化市| 茶陵县| 宜兰市| 通城县| 华亭县| 杭锦后旗| 兴安县| 本溪| 包头市| 东乌珠穆沁旗| 镇赉县| 都安| 汉阴县| 秦皇岛市| 武胜县|