- 您現在的位置：買賣IC網 > PDF目錄374047 > ADV7194KST (ANALOG DEVICES INC) Professional Extended-10⑩ Video Encoder with 54 MHz Oversampling PDF資料下載
參數資料
| 型號： | ADV7194KST |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 顏色信號轉換 |
| 英文描述： | Professional Extended-10⑩ Video Encoder with 54 MHz Oversampling |
| 中文描述： | COLOR SIGNAL ENCODER, PQFP80 |
| 封裝： | LQFP-80 |
| 文件頁數： | 45/69頁 |
| 文件大小： | 647K |
| 代理商： | ADV7194KST |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
ADV7194
–45–
REV. 0
APPENDIX 1
BOARD DESIGN AND LAYOUT CONSIDERATIONS
The ADV7194 is a highly integrated circuit containing both
precision analog and high-speed digital circuitry. It has been
designed to minimize interference effects on the integrity of the
analog circuitry by the high-speed digital circuitry. It is impera-
tive that these same design and layout techniques be applied
to the system level design such that high-speed, accurate perfor-
mance is achieved. The Recommended Analog Circuit Layout
shows the analog interface between the device and monitor.
The layout should be optimized for lowest noise on the ADV7194
power and ground lines by shielding the digital inputs and pro-
viding good decoupling. The lead length between groups of V
AA
and GND pins should by minimized so as to minimize inductive
ringing.
Ground Planes
The ground plane should encompass all ADV7194 ground pins,
voltage reference circuitry, power supply bypass circuitry for
the ADV7194, the analog output traces, and all the digital signal
traces leading up to the ADV7194. This should be as substantial
as possible to maximize heat spreading and power dissipation on
the board.
Power Planes
The ADV7194 and any associated analog circuitry should have
its own power plane, referred to as the analog power plane (V
AA
).
This power plane should be connected to the regular PCB power
plane (V
CC
) at a single point through a ferrite bead. This bead
should be located within three inches of the ADV7194.
The metallization gap separating device power plane and board
power plane should be as narrow as possible to minimize the
obstruction to the flow of heat from the device into the general
board.
The PCB power plane should provide power to all digital logic
on the PC board, and the analog power plane should provide
power to all ADV7194 power pins and voltage reference circuitry.
Plane-to-plane noise coupling can be reduced by ensuring that
portions of the regular PCB power and ground planes do not
overlay portions of the analog power plane, unless they can be
arranged such that the plane-to-plane noise is common-mode.
Supply Decoupling
For optimum performance, bypass capacitors should be installed
using the shortest leads possible, consistent with reliable operation,
to reduce the lead inductance. Best performance is obtained
with 0.1
μ
F ceramic capacitor decoupling. Each group of V
AA
pins on the ADV7194 must have at least one 0.1
μ
F decoupling
capacitor to GND. These capacitors should be placed as close as
possible to the device.
It is important to note that while the ADV7194 contains cir-
cuitry to reject power supply noise, this rejection decreases with
frequency. If a high frequency switching power supply is used,
the designer should pay close attention to reducing power sup-
ply noise and consider using a three-terminal voltage regulator
for supplying power to the analog power plane.
Digital Signal Interconnect
The digital inputs to the ADV7194 should be isolated as much
as possible from the analog outputs and other analog circuitry.
Also, these input signals should not overlay the analog power
plane.
Due to the high clock rates involved, long clock lines to the
ADV7194 should be avoided to reduce noise pickup.
Any active termination resistors for the digital inputs should be
connected to the regular PCB power plane (V
CC
), and not the
analog power plane.
Analog Signal Interconnect
The ADV7194 should be located as close as possible to the out-
put connectors to minimize noise pickup and reflections due to
impedance mismatch.
The video output signals should overlay the ground plane, and
not the analog power plane, to maximize the high frequency power
supply rejection.
Digital inputs, especially pixel data inputs and clocking signals
should never overlay any of the analog signal circuitry and should
be kept as far away as possible.
For best performance, the outputs should each have a 300
load
resistor connected to GND. These resistors should be placed as
close as possible to the ADV7194 so as to minimize reflections.
The ADV7194 should have no inputs left floating. Any inputs
that are not required should be tied to ground.
相關PDF資料 |
PDF描述 |
|---|---|
| ADV7194 | Professional Extended-10⑩ Video Encoder with 54 MHz Oversampling |
| ADV7202 | Simultaneous Sampling Video Rate Codec |
| ADV7300A | Multiformat SD, Progressive Scan/HDTV Video Encoder with Six NSV⑩ 12-Bit DACs |
| ADV7300AKST | Multiformat SD, Progressive Scan/HDTV Video Encoder with Six NSV⑩ 12-Bit DACs |
| ADV7301A | Multiformat SD, Progressive Scan/HDTV Video Encoder with Six NSV⑩ 12-Bit DACs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7194KSTZ | 功能描述:IC ENCODER VIDEO EXT-10 80-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799 |
| ADV7194KSTZ | 制造商:Analog Devices 功能描述:TV / Video IC |
| ADV7195 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat Progressive Scan/HDTV Encoder with Three 11-Bit DACs and 10-Bit Data Input |
| ADV7195KS | 制造商:Analog Devices 功能描述:Video Encoder 3DAC 11-Bit 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:MULTI-FORMAT VID+PROGSCAN/HDTV ENCODERIC - Bulk |
| ADV7195KST | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat Progressive Scan/HDTV Encoder with Three 11-Bit DACs and 10-Bit Data Input |
發布緊急采購，3分鐘左右您將得到回復。