- 您現在的位置：買賣IC網 > PDF目錄379664 > AM79231 (Electronic Theatre Controls, Inc.) Intelligent Subscriber Line Interface Circuit (ISLIC) PDF資料下載
參數資料
| 型號： | AM79231 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Intelligent Subscriber Line Interface Circuit (ISLIC) |
| 中文描述： | 智能用戶線接口電路（ISLIC） |
| 文件頁數： | 21/28頁 |
| 文件大小： | 278K |
| 代理商： | AM79231 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Am79231 Data Sheet
21
Thermal-Management Equations (All Modes except Standby)
TIMING SPECIFICATIONS
Notes:
1. The P1
–
3 pins are updated continuously during operation by the LD signal.
2. After a power-on reset or hardware reset, the relay outputs from the Am79231 turn all relays off. An
unassuming state is to place the relay control pins, which are level triggered, to a reset state for all relays.
Any noise encountered only raises the levels toward the register lock state.
3. When writing to the ISLIC registers, the sequence is:
a. Set LD pin to mid-state
b. Place appropriate data on the P1
–
3 pins
c. Assert the LD pin to High or Low to write the proper data
d. Return LD pin to mid-state
4. Am79231 registers are refreshed at 5.33 kHz when used with an ISLAC device.
5. If the clock or MPI becomes disabled, the LD pins and P1
–
3 returns to 0 V state, thus protecting the Am79231
and the line connection.
6. Not tested in production. Guaranteed by characterization.
R3
A logic 1 on the RD3 signal turns the R3 driver on and routes current from the R3 pin to
the RYE pin. In the option where the RYE pin is connected to ground, the R3 pin can sink
current from a relay connected to VCCD.
Another option is to connect the RYE pin to the B (Ring) lead through a diode and connect
a test load between R3 and the A (Tip) lead. This technique avoids the use of a relay to
connect a test load. However, it does not isolate the subscriber line from the linecard. The
test load must be connected to the Am79231 side of the protection resistor to avoid
damage to the R3 driver.
I
L
< 5 mA
P
SLIC
= (
S
BAT
–
I
LRL
)
I
L
+ 0.3 W
P
TMG
= 0
I
L
> 5 mA
P
SLIC
= (
S
BAT
–
I
L
(R
L
+ 2
R
FUSE
))*I
L
+ 0.3 W
–
P
TMG
P
TMG
= (I
L
–
5 mA)^2
(R
TMG1
+ R
TMG2
)
TMG resistor-current is limited to be 5 mA < I
L
.
If I
L
< 5 mA, no current flows in the TMG resistor
and it all flows in the Am79231.
These equations are valid when
R
TMGX
(I
L
–
5 mA) < (
S
BAT
–
R
L
I
L
)/2
–
2
because the longitudinal voltage is one-half the
battery voltage and the TMG switches require
approximately 2 V.
Symbol
Signal
Parameter
Min
Typ
Max
Unit
trSLD
tfSLD
tSLDPW
tSDXSU
tSDXHD
tSDXD
LD
LD
LD
P1,P2,P3
P1,P2,P3
P1,P2,P3
Rise time Am79231 LD pin
Fall time Am79231 LD pin
LD minimum pulse width
P1
–
3 data Setup time
P1
–
3 data hold time
Max P1
–
3 data delay
2
2
μ
s
3
4.5
4.5
5
Driver
Description
相關PDF資料 |
PDF描述 |
|---|---|
| AM79231JC | Intelligent Subscriber Line Interface Circuit (ISLIC) |
| AM8127LTB | AM8127 Clock Generator |
| AMZ8127 | AM8127 Clock Generator |
| AM8127XTB | AM8127 Clock Generator |
| AM8127 | AM8127 Clock Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79231JC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Intelligent Subscriber Line Interface Circuit (ISLIC) |
| AM7924JC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Subscriber Line Interface Circuit |
| AM7924SC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| AM7926-1VC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| AM7926-2VC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。